Showing results: 1 - 15 of 32 items found.
-
SY-Flow-Beta -
Synectic Electronics
This range of Flow Beta Cold Water Flow Meters is available in 6 pipe diameter sizes/ flow rate ranges. These inferential multi-jet type meters have a direct reading register and are suitable for drinking water (75/33/EEC)/WRc/WRAS MID Approved R80 T50.
-
SY042 -
Synectic Electronics
Our SY042 4-20mA Current Loop Limiter has been designed to limit the maximum current in either a 0-20mA or 4-20mA loop. Powered by the current loop, therefore installation couldn’t be simpler.
-
SY091 -
Synectic Electronics
SY091 is a Rugged 24 bit portable strain gauge indicator, which can indicate the load present on one or two attached cells. Display measurements from plug in sensors. The sensors can be load cells LVDTs or pressure sensors. 2.4Ghz wireless connectivity is also an option. The unit has a 10.75mm 8 character (+/- 5 digit measurement) LCD display.
-
SY057 -
Synectic Electronics
SY057 Encoder Signal Splitter provides a convenient way of splitting a master encoder signal across multiple drives or motion controllers.
-
SY024 -
Synectic Electronics
The SY024 Frequency Scaler/Multiplier can be linked to most frequency generating devices. It can be set to multiply or divide the frequency by a simple set up. When a frequency output device like a flow meter gives insufficient pulses to give the accuracy you need, or too many pulses for your Programmable logic controller or frequency counter to handle, or if you have more than one frequency output device and the rates are different you can match them by multiplying or dividing and re-transmitting to match the outputs to one another or the capabilities of your PLC etc.
-
SY014 -
Synectic Electronics
Synectic’s SY014 Miniture Incell Bridge Amplifier is specifically designed to fit inside either transducers or strain gauged components.
-
SY-JUNCTION-IP67 -
Synectic Electronics
The SY-JUNCTION-IP67 load cell junction box is useful to parallel connection of load cells and take just one cable out to almost any indicator, either batch controller or a PLC.
-
SY040 -
Synectic Electronics
SY040 Load Cell Simulator High Precision Instrumentation generates a mV/V signal. A great high precision simulator to use for either test, calibrating and also troubleshoot strain gauge applications. A wide range of bridge resistances can also be simulated including 350, 700, 1000, 1400 & 2000 ohm. The range of preset switch positions include 0, 0.2, 0.4, 0.6, 0.8, 1.0, 2.0, 3.0, 3.5, 4.0 & 4.5 mV/V. The option of very fine adjustments is also possible as this instrument has a knob for continuously variable adjustments between the preset ranges. Users can make a connection via 4mm banana connectors mounted on top of the case.
-
SY028TRIP/AMP -
Synectic Electronics
The SY028 Load Cell Trip amplifier has a built in alarm functionality. Accepts millivolt inputs and switches each of two setpoint relay outputs for high and low level trips.
-
SY-Flow -
Synectic Electronics
The Macnaught Oval Gear Corrosive Chemical Flow Meter are a positive displacement oval gear flow meters that are designed for corrosive chemical measurement applications. This type of flow meter technology provides excellent batch accuracy and is not affected by either pulsating flow, high viscosity or low conductivity.
-
SY27 -
Synectic Electronics
The SY27 range of meter pulse splitters, often called meter pulse duplicator are designed to split and isolate pulses from *between 1 and 4 meter signals. Each input will be split into 2 solid state relay outputs eg;4 in 8 out. It works with inputs from reed switch signals, with automatic de-bounce, as well as with high frequency pulses.
-
SY027 -
Synectic Electronics
Our SY027 Pulse Splitter is designed to convert pulses from meters or other turbine devices and transmit the same pulse via two relay outputs to enable two separate instruments to measure the rate simultaneously. It can be used with either electricity, water or gas meters (NOT ATEX). The SY027 PSO has been designed for applications where a pulse is required to be isolated, re-powered and repeated on two separate outputs. It works with inputs from reed switch signals, Opto coupler, open collector, NAMUR or TTL pulse (up to 25V) with automatic debounce, as well as with high frequency pulses. The speed of pulses can be accommodated from either a very slow to super-fast. Isolated relay outputs can be created by the PSR version when an NPN pulse output from a meter needs to be converted to a single relay isolated output or two.
-
SY-Flow-RCDL -
Synectic Electronics
Our RCDL Nutating Positive Displacement Flow Meter series is a positive displacement meter. It combines the accuracy of positive displacement meters with the reliability of nutating disc technology.
-
SY037 -
Synectic Electronics
The SY037 passive pulse splitter is ideal for converting pulses from meters or other turbine devices and transmitting the same pulse to three outputs to enable three separate instruments to measure the rate simultaneously. It needs no power supply. It functions simply from the pulses of the meter driving it. It is convenient for meters and any pulse generating device with reed switches, open collector or current source.
-
SY020 -
Synectic Electronics
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.