Systems Engineering & Management
state-of-the-art telemetry receiving systems and signal simulators for missile and aircraft flight testing; analog and digital video transmitters, receivers and surveillance systems for overt and covert surveillance; wireless RF modules and control systems for robotics applications; and wireless streaming video systems for tactical military requirements.
- 800-995-0636
760-727-7800 ext. 1100 - 760-727-5200
- info@semco.com
- 1430 Vantage Court
Vista, CA 92081
United States
Filter Results By:
Products
Applications
-
product
RF Down-Converter
CDC100A
Systems Engineering & Management
The CDC100A Series Down-Converter is a 1U rack-mount device designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a synthesized down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 1415-2485 MHz. The CDC100A is provided as a 1U Expansion Chassis that communicates with any SEMCO receiver via an RS-485 protocol. The communications I/O is via RJ45 and the operator interface is via the receiver RCMS GUI.
-
product
RF Down-Converter
CDCM100A-2
Systems Engineering & Management
The CDCM100A Series Down-Converter is an IP-67 rated device designed for installation on antenna pedestals. It is a pressurized, water-proof module designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a block down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 300-1150 MHz.
-
product
RF Multi-Coupler
MC108-2
Systems Engineering & Management
The MC100 Series Multi-Coupler is a 1U Rack-Mount device that provides RF distribution form 200 MHz to 5250 MHz. Both single and dual output configurations are available, as well as up to 8 output channels. Each output is an independent channel with +/- 5 dB gain controls, providing the ability to balance all outputs within +/- 1 dBm. Frequency Channel selection is from both front panel controls as well as remote control via Ethernet and SEMCO's MCCS Network software program.
-
product
Telemetry Receiver
TR70 Series
Systems Engineering & Management
The TR70 series of telemetry receiver products are stand-alone, multi-channel, multi-band systems designed for use with fixed antennas.
-
product
Telemetry Receiver
TR70RM Series
Systems Engineering & Management
The TR70RM series of telemetry receiver products are stand-alone, multi-channel, multi-band systems designed for use with fixed antennas.
-
product
Telemetry Signal Simulator
TSS200A
Systems Engineering & Management
Rack-Mount Telemetry Signal Simulator. The TSS200A Series Telemetry Signal Simulator is a 2U rack-mount configuration with a front panel 4.3" Touch Screen Control and Display, local GUI and Keyboard display and keyboard I/O as well as remote control via Ethernet using the SGCMS Remote Network Software. A removable front panel Solid State Drive and USB ports provide the ability to segregate both classified and unclassified telemetry signal simulation.
-
product
Telemetry Transmitter
TT22 Series
Systems Engineering & Management
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
product
Automated Telemetry Test Station
ATTS5000
Systems Engineering & Management
The ATTS 5000 was developed by SEMCO to ensure that receiver systems successfully perform at both IRIG 118 Chapter 4 recommended tests, as well as additional customer-specified performance parameters. The ATTS 5000 ensures that the highest quality test data is consistently and repetitively collected on each and every system.
-
product
Video Distribution Systems
VDU-100 Series
Systems Engineering & Management
SEMCO'S tactical military products have been developed in response to the requirement for near real-time, high-quality, encrypted video and sensor data capture, transmission and distribution in support of covert and overt military operations. These products provide for unprecedented audio-video and data communications from warrior-to-warrior as well as from warrior-to-command. Transmission modes include tactical and handheld radios, wireless and wired LAN, SATCOM, wireless Mesh, and Cellular, with full motion video capability in as low as 125 Kbps bandwidth. Video resolution, bandwidth and frame rates are adjustable, with high quality video frames capable of being transmitted in bandwidths as low as 9 Kbps. These products include video recording, with both local and remote download capability, as well as remote video enhancement, pan, tilt and zoom control, and multiple NTSC/PAL camera and imaging device interfaces. With administrative and password control, these products provide for unlimited remote viewing on PCs, Androids, iPhones and iPads anywhere in the world.
-
product
Telemetry Receivers
2U R200A Series
Systems Engineering & Management
R200A Series Receivers are designed for fixed and mobile Telemetry Ground Stations, but particularly for mobile applications where space is at a premium. The R200A provides for many of the same configurations and options available with the larger R600A and R400 systems, using the same cards, modules and RCMS network software for optimum interoperability. In addition, the RT200 Tracking Receiver configurations are an extremely popular, low cost solution for antenna tracking installations. The R200A provides the same proven performance and reliability and user interface of the R600A and R400. Like the R600A and R400, a "non-PC" configuration is available for remote operation via Ethernet. The 2U R200A receiver has become one of SEMCO's most popular receivers in terms of small form factor and operational performance and reliability.
-
product
Telemetry Repeater
TRT400
Systems Engineering & Management
SEMCO's TRT Telemetry Repeaters provide for reception and re-transmission of telemetry down-links in applications determined by link margin analysis. The TRT unit typically consists of a receive antenna and SEMCO's R100, R200 or R400 Series Receiver that is configured to support the required transmitted frequency bands. The demodulated telemetry signal is then re-transmitted in a different frequency band by a 5, 10 or 20 watt transmitter and antenna installed in the TRT Repeater. The TRT is housed in a ruggedized, portable enclosure and is designed to withstand harsh outdoor environments
