Showing results: 1 - 15 of 41 items found.
-
FW1.5 -
Bemco Inc.
The Bemco FW1.5, mechanically cooled Compact Humidity Chamber, has a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH. This chamber features direct dry air injection and a direct humidity sensor.
-
FB1.5V-UHC Series -
Bemco Inc.
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
BE-DE -
Bemco Inc.
Bemcoil-DE (double embossed) is made from roll and continuous welded 18 gauge 304 stainless steel sheet. Each tube passage is almost equivalent to a 7/8 inch OD tube. It is available in three finishes. A number 2B (semi-reflective) finish on the inside face and a number 4 (polished unidirectional) finish on the outside surface, specified when one side of the shroud is to be painted with black epoxy.
-
PTS DII -
Bemco Inc.
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
FW30 -
Bemco Inc.
The Bemco FW30, mechanically cooled, Glass Door Humidity Chamber has a temperature range of -18 C to +94 C (0 F to 200 F) and a humidity range of up to 5% RH to 95% RH. This chamber features dry air injection and a direct humidity sensor. It operates without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allows operation at 20% RH at 5 C and 50% RH at -14 C!
-
HPG -
Bemco Inc.
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
HV -
Bemco Inc.
Bemco's high vacuum components are not just another copy, but are superior solutions for the application. They are precision engineered for a specific application where a more common vendor's part will not do, or they incorporate refinements not yet available in commercial products. A custom liquid nitrogen chevron insert for a trap and an eight inch diameter compound elbow are shown above.
-
FW Series -
Bemco Inc.
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
PITC -
Bemco Inc.
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
TS Series -
Bemco Inc.
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
AF Series -
Bemco Inc.
AF Series chambers include a 304 Series stainless steel welded inner pressure liner with high temperature fiberglass insulation. No asbestos is used in chamber construction. The chamber liner is reinforced in accordance with Section VIII (Unfired Pressure Vessels) of the ASME Code.
-
FTU Series -
Bemco Inc.
The Bemco FTU Series temperature chambers are designed for use with universal (physical) test machines to allow evaluation of specimens under controlled environmental conditions.
-
AFW Series -
Bemco Inc.
AFW Series chambers include a 304 Series stainless steel welded inner pressure liner with high temperature fiberglass insulation. No asbestos is used in chamber construction. The chamber liner is reinforced in accordance with Section VIII (Unfired Pressure Vessels) of the ASME Code.
-
FL-I -
Bemco Inc.
Bemco integral chambers include a heliarc welded, 300 Series stainless steel inner liner, fiberglass insulation, and a structural steel supported, carbon steel outer case finished in Bemco blue. Stainless steel and other exterior materials are also available. No asbestos is used in chamber construction.
-
FL-M -
Bemco Inc.
Prefabricated chambers, rooms, and drive-in facilities, made from sectional panels, can be constructed in any size ranging from the very small to the extremely large. They are often a first choice when there is restricted access to the final assembly location or when initial cost is an important consideration. We manufacture a complete line of both prefabricated modular chambers, assembled from sectional panels on site, and welded integral chambers.