Gigasense
Gigasense AB was formed in 1951 as PIAB. The company marketed its products under the PIAB brand, including the famous PIAB dynamometer. In 2008, it changed its name from PIAB Sverige AB to Gigasense AB, and the Gigasense Anti Collision System was brought into the range. In 2010, Gigasense acquired JK Lab Instrument AB, which became one of its subsidiaries.
- +46 8 540 839 00
- +46 8 540 213 64
- info@gigasense.se
- Stationsvägen 16
Åkersberga, SE-184 50
Sweden
Filter Results By:
Products
Applications
-
product
Crane Weigher (Scale)
The PIAB Crane Weigher is a high accuracy all- weather instrument for force measurement in aggressive environment. The PIAB Crane Weigher is suitable both for in- and outdoor usage. Supply your PIAB Crane Weigher with PIAB Remote Read-Out Instruments for convenient display.
-
product
Dynamometer
The PIAB Dynamometer is excellent for measurement and control of tension forces and weight, where accuracy, reliability and safety in all conditions is required. The PIAB Dynamometer conforms to the International Standards for Safety Inspectorates. The PIAB Dynamometer is an all-weather instrument, equally suitable for use in the laboratory as in the field for weighing and measuring mechanical tension forces.
-
product
Load Pins
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
product
Rope Tension Meter
RTM
The PIAB RTM Rope Tension Meter is very simple and handy to use. Simply hold and “clip” it to the rope to be tested and use the large hand screw to deflect the rope to a fixed angle. The resultant force will affect the load cell and measure the tension in the wire rope. The resultant signal is digitally processed and displayed in a selected pre programmed graduation. The PIAB RTM 20D can be graduated in kN, klbs or in ton.
-
product
Sharp Edge Tester
SE400
The Sharp Edge Tester is used for determining the sharpness of edges of electrical equipment and other consumer products. A special tape is mounted on a spring loaded arm and dragged over the sharp edge. The tape is then inspected for damages.
-
product
Test Fingers & Probes
Test Fingers and Probes are used in most standards to check accessibility to moving parts or hazardous live parts. They comes in many forms, such as test fingers, test rods, test balls etc.
-
product
Wireless Loadlink
This wireless load link is designed to be light, accurate and easy to handle. It is supplied with a handheld monitor/indicator unit, calibration certificate, manual and a plastic carrying case.
-
product
Ball Pressure Tester
4710
The ball pressure tester is used to test the thermal properties of insulating materials. The test sample is placed in an oven and a steel ball is pressed against the surface. The impression of the steel ball is measured to see if it meets the requirements.
-
product
Anti Collision
GIGASENSE® is a fail-safe anti-collision system / collision avoidance system for track bound cranes (EOT) or similar equipment in tough industrial environment. The GIGASENSE anti-collision system is easy to install, robust, maintenance free and comes with built in self diagnostic functions to monitor the system. The microwave technology makes it especially suitable for steel-works, harbors and the like environments.
-
product
Load Cells
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
product
Crane Safety Monitor
CSM
PIAB CSM Crane Safety Monitor is an electronic control unit to be used in overload protection systems. The PIAB CSM evaluates and computes signals from force transducers and can be set for alarm at preset alarm limits. By installing the PIAB CSM, hazards for personnel and material are avoided. The PIAB CSM will also record the operation of the hoist. The PIAB CSM is designed both for indoor and outdoor operation in aggressive and demanding industrial environments.
-
product
Force Transmitter
LKVE/i
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
product
Impact Hammer
5111, 5112, 5113
The Impact Hammer simulates mechanical impact to the surface of the enclosures of electrical appliances and components.