Showing results: 1 - 15 of 42 items found.
-
ULP-25O & ULP-25T -
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
-
Unitech Scales And Measurements Pvt. Ltd
PiezoElectric Trainer comprises of piezoelectric crystal mounted inside housing and fitted on a base plate. Digital indicator is supplied to indicate the vibrational force.
-
Unitech Scales And Measurements Pvt. Ltd
Pressure Measurement Trainer comprises of strain gauge based pressure cell, foot pump to build the pressure, pressure tank fitted with release valves and a bourdon pressure gauge. Digital pressure indictor to read the pressure in Kg / Cm² is provided.
-
Unitech Scales And Measurements Pvt. Ltd
Torque Measurement Trainer comprises of strain gauge based reaction type torque transducer, fulcrum arm of 1 M length with L angle to mount the sensor, Pan & weights with digital torque indicator to read the torque in Kg-m.
-
Unitech Scales And Measurements Pvt. Ltd
Capacitance Trainer comprises of parallel plate/angular capacitor with dielectric medium air as sensor, mounted on the base plate with scale for displacement. Digital indicator is provided to read the change in capacitance in terms of displacement.
-
Unitech Scales And Measurements Pvt. Ltd
L.D.R. Trainer comprises of light dependent resistor (LDR) fitted to the shaft, which moves inside the tube where lamp is fitted at the other end. Variable DC voltage source is provided to vary the light intensity. Digital indicator is supplied to measure the light intensity in terms of distance moved between LDR and light source.
-
Unitech Scales And Measurements Pvt. Ltd
Vibration Measurement Trainer comprises of vibration generator of capacity 5 Newton with vibration exciter. Piezoelectric accelerometer is used to sense the vibration. Digital display unit will display displacement, velocity & acceleration sensed by the sensor.
-
Unitech Scales And Measurements Pvt. Ltd
* Study of PLC and its accessories. * All above circuits. * Introduction of timer, counter in all above circuits. * Interfacing PLC with Mimic panel. * Many circuits used in Washing Machine, process controls, drilling machines, etc,.
-
Unitech Scales And Measurements Pvt. Ltd
Level trainer is a table top module, it comprises of measuring tank of 50 CM length, sump tank and load cell capacitance as level sensor. A vertical pump is fitted circulate the water. Digital display indicator is provided display water level in cm
-
ULP-27 -
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.*UNITECH’S Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. *The stainless steel construction permits the transducers to operate in rugged, industrial environments. *We also undertake custom-built pressure transducer for specificrequirement and for OEM users.
-
Unitech Scales And Measurements Pvt. Ltd
Unitech offers tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed. Tool dynamometers are useful to study, analyse the optimum feed, speed and depth of cut on different materials. The dynamometers are also available in various capacities as per customer requirement.
-
UIG-17 -
Unitech Scales And Measurements Pvt. Ltd
Unitech offers tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed. Tool dynamometers are useful to study, analyse the optimum feed, speed and depth of cut on different materials. The dynamometers are also available in various capacities as per customer requirement.
-