Educated Design & Development, Inc.
Educated Design & Development, Inc. (ED&D) is a leading manufacturer of test equipment for product safety applications. Whether you are testing to CSA, UL, VDE, IEC or other requirements, ED&D is the world's best source. Ed&D is the only company in the world that can provide you with everything you need for Product Safety testing applications.
- 800-806-6236
919-469-9434 - 919-469-5743
- info@productsafet.com
- 901 SHELDON DRIVE
Cary, NC 27513
United States
Filter Results By:
Products
Applications
-
product
Loading Devices
Educated Design & Development, Inc.
Built-in fans provide sufficient coolingSelf-contained unit eliminates hazards due to exposed wiringFine tuning mechanism allows for ultra precise measurementsUnits are on casters, providing a portable test station!
-
product
Power Control
Educated Design & Development, Inc.
As a general purpose dual-voltage isolation transformer for step-up (120 to 240 VAC), step-down (240 to 120 VAC), or straight 1:1 isolation (120 to 120 VAC or 240 to 240 VAC). Models with a suffix "UC" are provided with a safety jack for access to the transformer secondary center tap (connected to the transformer center tap only in the 240 VAC output setting). This connection may be used in conjunction with a Dielectric Voltage Withstand test.
-
product
temperature Measurement
Educated Design & Development, Inc.
Up to 8 resistance reading channels, 4-wire methodUp to 12 temperature reading chanels, use of Type K, 24 AWG, Teflon thermocouplesIn the Box:8 - data cable (Cat5e) to connect the isolation modules to the Resistance Reading Channels8 - Isolation Module connected between the HOT-30 and EUT (Equipment Under Test) to isolate high voltage8 - Banana Jack Sets (2 red, 2 black), to replace Kelvin Leads in tight places8 - Kelvin Probe Set12 - 72 inch K Type Thermocouple1 - USB2.0 Type A (standard) to Type B USB cable
-
product
Voltage, Current and Power Measurement
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
product
Digital Leakage Current Tester
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
product
Environmental Testing
Educated Design & Development, Inc.
Incredible size / features at a phenomenal price! A must have when a larger chamber is needed. Easy to use, microprocessor based digital controls. Standard models are heat/humidity Humidity range of 10-96%, temperature range of 35°-70° C, Refrigeration can be added for cold testing to -10°. Chamber inside dimensions are 34x28.5x60 in. (87x73x153 cm), many options are available including chart recorder, RS232, programmable ramp/soak, viewing window and CO2 system.
-
product
Automated Digital Ground Continuity Tester
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
product
IP code Testing
Educated Design & Development, Inc.
Complies with various IEC, EN, CE, VDE, UL & CSA requirementsUnit comes with NIST traceable / ISO 17025 accredited certificate of calibration.ED&D is ISO 17025 accredited by ACLASS, an ILAC Member. Measurement data and uncertainty data is available.Uses RTS-01 Rain Spray Head
-
product
Plug Socet & Cord Testing
Educated Design & Development, Inc.
Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.
-
product
Impact Testing
Educated Design & Development, Inc.
1250 g body includes release mechanism and striking element guide.250 g striking element comes with cocking knob and hammer head, polyamide face, is hemispherical with a radius of 10 mm, has a hardness of HR85-100.60 g release cone with a 10N release force.Single Impact Force models range from a 0.2 J Hammer to a 2.0 J Hammer.Custom padded carrying case included.
-
product
Flame & Other Plastics Testing
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
product
Switch Testing Machines
Educated Design & Development, Inc.
1 or 3 actuating device(s) for rocker switches and push- button switches with 2 single-acting pneumatic cylinders each, with air throttle valves to adjust the actuating speed, height-adjustable mounted to holders, with multiple adjustable specimen holders, with safety sockets to connect the specimens to external test voltages and loads1 housing, made of steel, with protective hood1 plug-in unit with front panel for operating the devices.1 Control device for the entire unit:main switch with EMERGENCY OFF function, safety switch for the protective hood, mains cord and fuses1 control device for each actuating device:programmable control unit with exchangeable program modules (containing the "test rhythm") and for adjusting and indicating the test parameters "number of strokes" and "stroke time", start and stop push-buttons, push-buttons for moving manually the cylinder pistons and as actuation indicator for the cylinder
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
