Showing results: 61 - 75 of 79 items found.
-
TWA Advanced Series -
Amperis sl
The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.
-
Nexus 1450 -
Amperis sl
The Nexus 1450 is a powerful state-of-the-art power meter that provides high-precision electrical energy measurements and records waveforms. This equipment allows you to measure power quality and determine the reliability of electrical power. The Nexus 1450 meter allows you to see the reliability of the power circuit to determine the causes of failures, surges and voltage drops, and harmonics.
-
Handheld Turns Ratio & Winding Resistance Tester TWR-H -
Amperis sl
TWR-H is a handheld, battery operated, fully automatic test set specially designed for turns ratio, phase shift, excitation current and winding resistance measurements of transformers. It can also perform demagnetization of these transformers. Transformer turns ratio is determined by applying AC voltage across high voltage winding, accurately measuring AC voltage across the corresponding unloaded transformer winding, and then displaying the ratio of these voltages. User can enter a transformer’s nameplate voltages, so that turns ratio deviation can be calculated. This feature eliminates any error otherwise caused by an operator’s manual calculation. TWR-H compares measured turns ratio with the nameplate ratio and prints out the % of error for each test. Transformer winding resistance is determined by injecting DC current through a winding, accurately measuring DC voltage across the winding, and then calculating resistance as the ratio of voltage and current. The device generates true DC ripple-free currents. Both the injection of the current and the discharge of energy from transformer magnetic circuit are automatically regulated.
-
SHARK 200 -
Amperis sl
*Compact design*Class 0.2 in energy, typical accuracy 0.1%*Front serial port for programming once installed*Integrated RS-485 (Modbus and DNP 3.0 protocols)*Self-range in voltage and current
-
TWA Standard Series -
Amperis sl
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
RMO-G -
Amperis sl
The RMO-G series micrometers are designed with the latest technology to generate a DC ripple-free current with automatically regulated test ramps, no magnetic transients and very efficient filtration.
-
CoroCAM 7 -
Amperis sl
The CoroCAM 7 corona effect camera is a camera used to visualize and locate corona and electric arc discharges. This camera shares the same ultraviolet imaging system as coroCAM 6D, but additionally combines it with a high-performance visible camera and viewfinder. This camera is used for high voltage inspections.
-
CoroCAM 6D -
Amperis sl
The CoroCAM 6D corona effect camera is a robust, lightweight and easy to operate camera with an ultraviolet imaging system. It stands out for its innovative design and improved sensitivity, which allows for higher quality inspections. Sensitivity has been improved thanks to the blind solar filter packages and the low noise, high sensitivity detector.
-
APQM-702/APQM-703 -
Amperis sl
*It can be powered from the L phase.*It is intended for use in virtually all types of networks from 64 V to 760 V directly, with special consideration for measurements on low-voltage poles, due to its ease of connection.*It has an independent power supply and is therefore particularly suitable for measurements outside of voltage transformers. It can also be adapted for measurements on DC voltage systems.*Real-time remote configuration and data transfer (GPRS) using a built-in GSM modem
-
PULD 40 -
Amperis sl
The PULD-40 is a versatile and highly accurate ultrasonic inspection system designed to meet the needs of our customers.
-
AMPI-530 -
Amperis sl
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
TAND220A -
Amperis sl
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
APQM-707 -
Amperis sl
This equipment is a power quality analyzer according to the European standard EN 50160. The Amperis APQM-707 is a high-tech product that allows universal measurement of the parameters of 50/60 Hz electrical networks, as well as the analysis and recording of these parameters.
-
APQM-711 -
Amperis sl
The APQM-711 wave quality analyzer enables measurement, analysis and recording of 50/60 Hz network parameters and wave quality diagnostics according to EN 50160. The APQM-711 is an innovative and unique model, it has Wi-Fi communication with the included tablet. The tablet allows all operations to be carried out remotely and with its 10" touch screen it is very easy to operate. From the tablet you can operate the analyzer intuitively and quickly, we can also perform the preview of live data and reading and analyzing data stored in internal memory.
-
PADD -
Amperis sl
We developed the PADD for the detection of internal and external partial discharges on metal oxide lightning rods. Defects can cause radio interference in communication systems or TV images, interference whose origin is very difficult to locate. We have developed a unique technology for detecting radio frequencies for use under voltage.
