Array Solutions
Array Solutions' products are in use at top DX and Contest stations worldwide as well as commercial and governmental installations.
- 214 954 7140
- 214 954 7142
- 2611 N Beltline Rd
Suite 109
Sunnyvale, TX 75182
United States
Filter Results By:
Products
Applications
-
product
RX Pre-Amplifier System
RAM-34
The RAM-34 is a complete pre-amplifier system designed primarily for the low bands 160M thru 40M. It has inputs for four receive antennas and internal 3-pole bandpass filters for 160M, 80M and 40M. In addition to the pre-amplifier, it has a step attenuator that togetherwith the amplifier stage provides gains from -20 dB to +20 dB in 5 dB steps. This allows equalizing the signal levels between the antenna inputs. Gain settings are memorized for each antenna on each band. Different types of receive antennas have different signal levels and the gain memories eliminate the need to adjust the receiver or pre-amplifier when switching between the antennas.
-
product
Antenna Switch
SixPak
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
product
Master Controller
RatMaster
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
product
Transmitter Inhibit Controller
ALC-1
The Array Solutions ALC-1 Transmitter Inhibit controller interfaces between your amplifier’s ALC output, your PowerMaster PTT connections, and your transceiver’s ALC input to provide fast, rapid protection of your transceiver and amplifier when a sudden high SWR event occurs.
-
product
Shortwave Power Amplifier
OM4001A
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
product
4 Antenna Phase Controller
StackMaster
This controller comes in two versions and is configurable to support all of the Array Solutions products. The version with the 11 output relays is meant to be used with the StackMaster and is described below.
-
product
VHF & UHF Couplers for the PowerMaster and PowerMaster II
VHF-1.5K (2m), VHF-1.5K-2 (1.35m), UHF1.5K (440-450 MHz), UHF-1.5K-2 (420-440 MHz)
-
-
product
Push Button Controller
Stack-Match II
Stack Match controller is a replacement for the rotary switch Stack Match controller. It features pushbutton switches for easy antenna selection and has outputs for both phase control and an auxiliary output. It is a component of the ShackLAN product line and as such can be fully remotely controlled via computer with our ShackLAN Control Center software. All outputs are switched with relay contacts for maximum reliability and power for the external switching unit may be applied from a separate power source to provide maximum isolation from the ShackLAN network. There is also a PTT input to allow different stack configurations for transmit and receive.
-
product
Phasing for Mono-Band & Multi-Band Antennas
StackMatch
The StackMatch control switch box has a rotary switch and three LEDs which display the antennas selected. Think of the three LEDs as the antennas arranged on a tower with number 3 in the ▲ being at the top of the tower, number 2 in the ● being in the middle, and number 1 in the █ at the bottom of the stack. As the rotary switch is turned these LEDs will light up in a pattern which indicates which antennas are being fed power from the StackMatch. You will see these symbolsalso on "little towers" or lines arranged around the rotary switch knob. Just point the knob to the desired pattern and the LEDs will light to indicate in the same pattern as chosen with the switch.
-
product
Triangular Array
W8AV
We have under-rated the power this system can handle to assure the user high reliability under heavy use such as in a 48 hour radio contest. Please contact us if you have any questions about the product and please send a picture and description of your station showing the Triangle Array control system installed and in use.The W8AV system has two components: a relay box that will be mounted midway between the three verticals and a control box that is connected with a 4-wire control cable inside the operating room.
-
product
2 Vertical Multi Band Phase System
W9AD
The system will produce a broadside pattern and an end fire pattern figure 8 as well as other lobes and nulls in the various directions as you change the combinations. One should model this antenna using EZNEC or some other antenna modeling program to determine the patterns which are available to the user on all bands of use.
-
product
Control Wires Surge Suppressors
AS-8SP / AS-12SP / AS-16SP
Array Solutions Control Wires Surge Suppressors
-
product
1.8-148 MHz Stand Alone Weatherproof Unit for the Application of DC Control Signals up to 400ma on your Coax Cable
Bias-T PLUS
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
product
Digital RF Power &VSWR Measurement System
PowerMaster II
Thank you for purchasing the Array Solutions PowerMaster II RFPower/VSWR Indicator. The PowerMaster II represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster II also features the ability to be monitored and controlled from a PC using the software downloadable from our website, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster II firmware updates will be posted for download from the Array Solutions website as they become available. This means that the user can take full advantageof features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates
