Showing results: 16 - 30 of 158 items found.
-
MS 1711 -
Meltronics Systemtech
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
MS 1720 -
Meltronics Systemtech
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
mS 1115 -
Meltronics Systemtech
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
MS 1100 -
Meltronics Systemtech
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
MS 2011 -
Meltronics Systemtech
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
MS 2014 -
Meltronics Systemtech
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
-
MS 2010 -
Meltronics Systemtech
Receiver Exciter is used to receive and transmit HF range signals & processing HF signals into voice and data format using DSP technology. It consists of high quality HF receiver and HF exciter. System has SELCAL and secure communication features. System has configuration facility for Frequency range, mode of operation (AM, LSB, USB, DATA, CW), volume, squelch level from external control unit. The exciter produces the low power signal which is fed to the power amplifier unit.
-
MS 1103 -
Meltronics Systemtech
*Checks integrated functionality of UAV*During integration checks it performs the functions of the Ground Control Station*Interface with Target Group Set (TGS)*Information is decoded and displayed in the display panel
-
MS 1122 -
Meltronics Systemtech
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
MS 1534 -
Meltronics Systemtech
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
MS 1741 -
Meltronics Systemtech
- Four FPDP front panel outputs- FIFO buffering for real−time recording- FPDP Outputs: Two 80−pin FPDP connectors (A and B)- FPDP Outputs: Two 80−pin FPDP connectors(C and D)- Quantity: Standard: Two Front Panel Data Port (FPDP) connectors, each providing 32−bit output- Output Type: FPDP I, non−inverted configuration FPDP II, double the selected clock rate- Clock: On−board clock- FIFOs- Quantity: Four IDT72V3690 FIFOs, one for each FPDP port- Size: 32,768 x 36- Speed: FIFOs are capable of 166 MHz speed, but are run at one half of sample clock speed
-
Meltronics Systemtech
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
MS 1821 -
Meltronics Systemtech
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
MS 1109 -
Meltronics Systemtech
The RF Tester is a computer-controlled system used to test the RF Unit, Logic Unit (ECM) and its modules.
-
MS 1721 -
Meltronics Systemtech
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA with ARINC 717 IP Core- One Channel ARINC 717 Transmitter and Receiver- Generates all PCM telemetry signals like NRZ, Bi-Phase, - Differential Bi-phase, DM signals- Used to test all types of PCM based telemetry equipments- Configurable output signals format (parity, word length, Minor, Major frame, Bit position)- User can configure the words and word positions in the frame- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future