Showing results: 76 - 90 of 158 items found.
-
MS 1830 -
Meltronics Systemtech
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
MS 1300 -
Meltronics Systemtech
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
MS 1502 -
Meltronics Systemtech
- ATE- Data Acquisition System- Process Control Industry- Industrial Automation
-
MS 1806 -
Meltronics Systemtech
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
MS 1800 -
Meltronics Systemtech
*Bus Interface:- 64 Bit PCI Bus with PMC Interface*Virtex-4 FPGA based design*32 channel digital I/O signal*RS232 & RS485 Interface*32MB Flash*2MB Static RAM for data storage*Analog Inputs:- 2 Channel*Input Resolution:- 14 Bits*Sampling rate up to 80MSPS*Filter:- Low Pass Filter for all channels*Two Analog Outputs*14 bit Resolution*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
MS 1602 -
Meltronics Systemtech
The MIP programmer is used to program, read and erase mission data of Mirage 2000 Aircraft. This system is micro controller based design. This system facilitates to program the four EPROM devices at a time. This system contains four read write slots and one read only slot. Read only slot used to read the device data safely. System also has capability to program the one slot device data to another slot device.
-
MS 1513 -
Meltronics Systemtech
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
MS 3630I -
Meltronics Systemtech
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
MS 3648I -
Meltronics Systemtech
Break in Break Out Box is standard portable 19” rack mountable with 128 Input and 128 Outputs.
-
MS 1718 -
Meltronics Systemtech
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
MS 1119 -
Meltronics Systemtech
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
MS 1715 -
Meltronics Systemtech
*Bus Interface:- 32 Bit/64 bit PCI Bus with cPCI Interface*Two slots of 32/64 bit PMC connector interface*Speed of operation up to 66MHz*64 bit, 66MHz PCI Bridge based design*Self Test future
-
MS 1501 -
Meltronics Systemtech
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
MS 3635I -
Meltronics Systemtech
CPCI Integrated Communication Card is high end Microprocessor based Mixed RS422 Communication and Differential Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have Synchronous RS422 Communication Interface, Asynchronous RS422 Communication Interface, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic storage and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
MS 1726 -
Meltronics Systemtech
*Bus Interface:- 32 Bit PCI Bus with 3 U Form factor*PCI to PCI Bridge Interface*Speed of operation up to 66MHz*1 1553B dual redundant channel*4 RS422 Channels*16 TTL I/O Channels*Message Storage Buffer*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
