Teledyne LeCroy

Teledyne LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types.

  • (800) 553-2769
    845 425-2000
  • 845-578-5985
  • 700 Chestnut Ridge Road
    Chestnut Ridge, NY 10977-6499

Filter Results By:

Products

Applications

Showing recent results 1 - 15 of 70 products found.

  • HDMI/HDBaseT Video Generator & Analyzer

    280 - Teledyne LeCroy

    The Teledyne LeCroy 280 HDMI/HDBaseT Video Generator (Tx) and Analyzer (Rx) is small compact, battery powered test set ideally suited for professional A/V integrators and home theatre installers. This convenient test set enables you to conduct basic verification and diagnostic tests on HDMI/HDBaseT cables, video distribution networks and individual A/V components. The HDMI input and output ports support testing up to 18 Gbps data rate and 600 MHz pixel rate and the HDBaseT input and output ports support testing up to 300 MHz pixel rate.

  • Network Analyzers

    SPARQ Series - Teledyne LeCroy

    The SPARQ Signal Integrity Network Analyzers are ideal for the engineer who wants to make S-parameter measurements quickly, easily, and at a fraction of the cost of a VNA. Fully calibrated measurements can be made in minutes, and without any need to connect or disconnect cables to calibration kit standards or electronic calibration modules.

  • M-PHY® Gear 1/2/3 UniPro/UFS Analyzer/Exerciser

    Eclipse M32 - Teledyne LeCroy

    The Eclipse M32 analyzes bi-directional UniPro and UFS traffic, performing protocol sequence and timing analysis and packet header and payload inspection, to provide complete protocol debug and analysis of UniPro and UFS devices. Trace Validation uses state machine logic to analyze captured traces algorithmically without user intervention. The Eclipse M32 also provides conformance/compliance verification, as well as margin, corner case, and automated stress testing.

  • Multi-Protocol Video Analyzer / Generator

    780E - Teledyne LeCroy

    The Teledyne LeCroy quantumdata 780E Multi-Protocol Analyzer / Generator is a handheld digital video generator and analyzer that enables you to run tests on various digital video devices and network distribution devices on site or in the R&D lab. The 780E instrument provides a 7 inch color touch screen for operation and for viewing status of outgoing and incoming video and audio. The 780E is equipped with DisplayPort, HDMI and HDBaseT interfaces. Each digital interface is supported by both an output port and an input port to allow testing of digital video sources, displays, audio devices and distribution devices. Testing hybrid converter devices supporting DisplayPort, HDMI, HDBaseT distribution networks is a key application of the 780E as well.

  • Motor Drive Analyzer

    MDA803A - Teledyne LeCroy

    The Motor Drive Analyzer is built on the 8ch/12-bit HDO8000A platform. It contains all of the advanced oscilloscope capability you need for embedded control debug plus three-phase power and mechanical analysis with accuracy to within 1% of a dedicated power analyzer instrument.

  • Logic Analyzers

    Teledyne LeCroy

    With the HDA125 High-Speed Digital Analyzer, Teledyne LeCroy has defined a totally new class of instrument – a high-performance logic analyzer module that can be combined with existing high-speed oscilloscopes to provide unparalleled mixed-signal measurement and analysis.

  • DC-Coupled 25 GHz Optical-to-Electrical Converter

    OE6250G - Teledyne LeCroy

    The OE6250G is a fully calibrated, DC-coupled 25 GHz Optical-to-Electrical converter - the first such instrument available. With a wide operating range of 800nm - 1600nm, it enables accurate acquisition of intensity-modulated optical signals on a real-time oscilloscope at baud rates of 28 Gbaud and beyond. For such applications, real-time oscilloscopes are gaining industry favor due to their inherent advantages in analysis and debug capability; the OE6250G enables users to leverage Teledyne LeCroy''''s class-leading feature set, including eye, jitter and noise analysis of NRZ and PAM4 signal types, on high-baud-rate optical signals.

  • High Definition Oscilloscopes

    HDO9000 - Teledyne LeCroy

    The HDO9000 with HD1024 Technology provides exceptional signal fidelity with 10-bit resolution and a superior oscilloscope experience to deliver faster time to insight. The HDO9000 and MAUI with OneTouch allows users to perform all common operations with a single touch of the display, optimizing for convenience and efficiency. Meanwhile, the 15.4” high resolution capacitive touch screen’s bright display and quick responsiveness further enhances the inherent efficiency and intuitiveness of MAUI with OneTouch

  • High-Voltage Differential Probes

    HVD3000A Series - Teledyne LeCroy

    The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.

  • High Voltage Optically-isolated Fiber Optic Probe

    HVFO - Teledyne LeCroy

    The HVFO measures only the low voltage sensor voltage across its leads. Therefore, the total RC load on the circuit is ~100 times less compared to a conventional HV differential probe. Furthermore, the low lead loop inductance, >100dB CMRR, and low attenuation provide superior signal fidelity, noise and rejection. By contrast, a conventional HV differential probe provides 100 times (or more) load on the circuit since the common-mode plus sensor signal voltage are measured across its leads. This excessive load will impact the signal fidelity and may even cause the circuit to malfunction.

  • Disk Drive Analyzer

    DDA 760Zi-A - Teledyne LeCroy

    Teledyne LeCroy Disk Drive Analyzers (DDA) assist data storage design engineers by integrating tools that improve the time to market of new products and accelerate understanding and failure analysis on existing drives. Teledyne LeCroy continues that tradition with the DDA 7 Zi-A Series equipped with its powerful Disk Drive Analysis toolset. Capture, view, and analyze the wave shape of high-speed, complex drive signals with speed and integrity.

  • Disk Drive Analyzer

    DDA 735Zi-A - Teledyne LeCroy

    Teledyne LeCroy Disk Drive Analyzers (DDA) assist data storage design engineers by integrating tools that improve the time to market of new products and accelerate understanding and failure analysis on existing drives. Teledyne LeCroy continues that tradition with the DDA 7 Zi-A Series equipped with its powerful Disk Drive Analysis toolset. Capture, view, and analyze the wave shape of high-speed, complex drive signals with speed and integrity.

  • Disk Drive Analyzers

    DDA 7 Zi-A Series - Teledyne LeCroy

    Based on the WavePro 7 Zi-A Series models, the DDA 7 Zi-A Series Disk Drive Analyzers are available in 3.5 and 6 GHz models and come equipped with 20 Mpts/ch acquisition memory. Dedicated disk drive measurements, trigger and zooming for failure analysis, and serial data measurement capability with a Disk Drive Analyzer user interface are also standard to address high capacity disk drive designs. Operate in either DDA or SDA mode to analyze the serial data links or the physical media behavior on a hard drive.

  • 100 MHz - 1 GHz Oscilloscopes

    WaveSurfer 3000z - Teledyne LeCroy

    The WaveSurfer 3000z has a 10.1" capacitive touch display, the longest memory, and the deepest toolbox. 00 MHz, 200 MHz, 350 MHz, 500 MHz and 1 GHz bandwidths. Up to 4 GS/s sample rate. Long Memory – up to 20 Mpts. 10.1” capacitive touch screen display.16 Digital Channel MSO option.

  • PCIe Protocol Analyzer/Jammer

    Summit M5x - Teledyne LeCroy

    The Summit M5x Protocol Analyzer /Jammer is the computer industry’s first platform to not only support today’s PCIe 4.0 specification but is designed to also support the next generation PCIe 5.0 (32GT/s) specification and introduces new error injection (jamming) capabilities for PCIe testing in addition to high speed recording and analyzing. The Summit M5x protocol analyzer/jammer features the PCIe industry’s first PCIe 4.0 compliant specification jamming test capability.