Showing results: 31 - 45 of 155 items found.
-
-
H71001000 -
6TL Engineering
This test base is ideal for table top applications, where with just some YAV modules and some external instrument (stack&rack stand alone instruments or PXI chassis) the test procedure is covered.
-
6TL Engineering
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
YAVAP955 -
6TL Engineering
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
YAV90084 -
6TL Engineering
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
AR438 -
6TL Engineering
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
YAV90057 -
6TL Engineering
The YAV90057 is a High density multiplexer, with 10-bank, 16-channel, 1 pole. It uses high quality electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 220VDC/250VAC.
-
YAV91CLR -
6TL Engineering
The YAV90CLR card allows the intensity and color test of LEDs, in an automatic, precise and cost-effective way. The card has a calibrated RGB light source as a tool for calibration of the 16 channels or for detecting dirt on the optical heads.
-
YAV90086 -
6TL Engineering
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAVAL964 -
6TL Engineering
- 16 channels DPDT or SPDT 2A- CAN bus control and 24Vdc (J1 and J2 connectors to chain multiple cards).- Access to relay-pins through wire-wrap or terminal block- Address selection DIP switch on top layer- LED monitoring- Drivers dll & VIs available
-
YAVP20T1 -
6TL Engineering
20 x Multiturn potentiometers Passive board Custom Values
-
YAV90097 -
6TL Engineering
32-Lines selectable High-Open-Low connection 3kV 1,0A Relays (Cool connection) Hipot test capabilities CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90304 -
6TL Engineering
8 x 24Vdc PNP Inputs 16 x 24Vdc 600mA PNP Outputs CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90077 -
6TL Engineering
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90HVT -
6TL Engineering
32 relays High Voltage (Up to 1500V) Multimeter/Amperimeter 14 bits resolution. 1x Analog Output and 2x Digital Outputs Internal automatic calibration CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available Automatic module identifier