Showing results: 31 - 45 of 210 items found.
-
Elcometer Limited
Produced specifically for the automotive aftermarket and Insurance Assessors, 3rd party consultants, body shops and used car sales, these kits provide an instant measure of the coating thickness of panels.An illuminated magnifier is supplied to enable close inspection of bodywork.Measurement parameters include:Surface temperatureSurface inspectionCoating thickness
-
215 -
Elcometer Limited
Memory stores up to 260,000 readingsIdeal for testing for powder or liquid coatings in batch or conveyor ovensVariable measurement interval, date, time, °C / °FHigh temperature resistant teflon coated probe cables are easy to clean after each runQuick display shows maximum temperature, Cure-Index figure and pass/fail for each probeMeasure up to 6 different temperatures at one timeIdeal in situations where powder coated thickness is inconsistentStart and stop logging at a pre-set temperatureLarge menu-driven display for easy operationPrint full colour report directly to any HP printerUSB data output to ElcoMaster® software and combine with other key inspection measurements
-
134W -
Elcometer Limited
The Elcometer 134W is used to monitor recycled water (after it has been applied) to establish effectiveness of salt removal, this test is ideal for testing the salt contamination in wash water and blast water.
-
138/2 -
Elcometer Limited
The Elcometer 138/2 Surface Contamination Kit provides the user with a means for testing invisible surface contaminants including:pHchloride ionsironsalts
-
510 -
Elcometer Limited
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent, repeatable adhesion strength resultsFully adjustable pull rates 0.1-1.4MPa/s (14.5-203psi) to meet National and International StandardsCan be used with 10,14.2, 20 and 50mm diameter dolliesUser definable limits with unique pressure hold and release functionUser definable measurement range with an accuracy of ±1% of full scale:10mm dolly: 100MPa (14400psi14.2mm dolly: 50MPa (7200psi)20mm dolly: 25 MPa (3600psi)50mm dolly: 4MPa (580psi)Dust and water resistant rugged design to IP64Interchangeable units: MPa, psi, Nmm2 and NA range of standard and thin substrate actuator skirts (compatible with Elcometer 506) available for adhesive strength testing on thick, thin, flat or convex substratesStore up to 60,000 readings with individual pull graphs in up to 2,500 alpha numerical batches, complete with attribute failure informationUSB and Bluetooth® data output - compatible with ElcoMaster® App for iPhone, iPod, iPad and Android mobile devices
-
103 -
Elcometer Limited
The Elcometer 103 Blast Nozzle Gauge measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in its performance. Nozzle orifice wear results in decreased productivity and increased abrasive media consumption.
-
102 -
Elcometer Limited
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Elcometer Limited
Surface cleanliness: Soluble salts & ion specific contamination (sulphates, chlorides, nitrates etc.) which are often invisible to the eye, together with amine blush (for amine cured epoxy coatings) can result in premature coating failure, resulting in high re-coating and maintenance costs. Elcometer has a range of test equipment for assessing surface cleanliness prior to applying a coating.
-
Elcometer Limited
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
Elcometer Limited
Surface Condition: degree or percentage of rust, level of mill scale, etc., can be visibly assessed using Pictorial Surface Standards. Weld beads can be assessed using a weld comparator and weld gauges.
-
122 -
Elcometer Limited
Elcometer 122 Testex® Tape consists of foam with a non-compressible backing. The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile. The profile of the surface can then be measured using the Elcometer 124 Thickness Gauge.
-
125 -
Elcometer Limited
Using the Elcometer 125 surface comparators as a reference the blasted profile can be compared to the four reference profile grades in each comparator. Profiles are recorded in microns.
-
129 -
Elcometer Limited
The Elcometer 129 Surface Comparators are available in two models to suit your requirements.
-
Elcometer 139 -
Elcometer Limited
The presence of amine blush is indicated by a visual change of colour of the test solution when compared with a control sample. The Elcometer 139 determines whether amine blush is or is not present on the coating’s surface.
-
Elcometer Limited
Users can either place a sample on the meter’s flat sensor or immerse the meter’s sensor directly into the solution under test. The Elcometer 138 can be used for a broad range of applications, including: soluble salt concentrations, the electric conductivity (EC) of solutions used in agricultural operations and measuring rainwater pollution levels.