Showing results: 61 - 75 of 189 items found.
-
Elcometer Limited
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
6910/3 -
Elcometer Limited
The Elcometer 6910/3 Setaflash ‘Series 3’ Active-Cool Closed Cup Tester offers the same features as the Elcometer 6910/1 Setaflash but is fitted with a cup suitable for testing corrosive samples.
-
Elcometer 6910 -
Elcometer Limited
The Elcometer 6910 Setaflash ‘Series 8’ Active-Cool Closed Cup Tester offers the same features as the Setaflash ‘Series 8’ Closed Cup Tester but is designed with a temperature range of -30°C to 135°C (-22°F to 275°F) with no external cooling required.
-
-
2210 -
Elcometer Limited
The Elcometer 2210 Zahn Dip Cup is a small U-shaped viscosity cup suspended from a looped wire.
-
Elcometer Limited
Visual appearance can determine a person’s perception of a product. Colour and Gloss are two key parameters that are used to define a product’s overall quality. Perception is subjective, but Elcometer’s range of gloss meters, DOI meters and colour assessment equipment can quantify appearance measurement. The ability of a surface to reflect light without scattering is known as gloss. Using a gloss meter, gloss is measured by directing a constant intensity light beam at a fixed angle to the test surface and then by monitoring the amount of reflected light at the same angle. Different surfaces require different reflective angles.
-
134W -
Elcometer Limited
The Elcometer 134W is used to monitor recycled water (after it has been applied) to establish effectiveness of salt removal, this test is ideal for testing the salt contamination in wash water and blast water.
-
Elcometer Limited
Blasting parameters: A number of important parameters need to be monitored during the blasting or water jetting process, these include: air pressure (at the nozzle), nozzle diameter, blast media contamination & pH values in order to avoid recontamination of the substrate during blasting.
-
Elcometer Limited
Measurement parameters include:*Surface assessment*Blast equipment inspection*Surface profile*Surface contamination
-
2434 -
Elcometer Limited
Thanks to its handle, the Elcometer Frikmar Viscosity Dip Cup is very easy to use to perform viscosity checks on site or during the manufacturing process.
-
1537 -
Elcometer Limited
The Elcometer 1537 ISO Scratching Tool is a simple but effective instrument that is used to scratch the surface of samples in preparation for adhesion, salt spray and corrosion tests.
-
129 -
Elcometer Limited
The Elcometer 129 Surface Comparators are available in two models to suit your requirements.
-
308 -
Elcometer Limited
The Elcometer 308 Hygrometer has been specifically designed for use in very hot climates where the surface temperature of the substrate can exceed the paint manufacturer’s recommended limits for successful painting.Painting outside recommended limits can have a detrimental affect on the performance and lifetime of the coating.Key features of the Elcometer 308 Hygrometer include:Rugged design: Suitable for use in extreme environments the Elcometer 308 Hygrometer is dustproof and waterproof with fully sealed sensors.Measurement Hold / Release function: With a single button press readings are ‘held’ on the screen. These can then be recorded before simply pressing the button again to ‘release’ the screen and continue to take further readings as necessary.Backlight: Bright screen making information easy to read – ideal in dark or confined spaces.
-
122 -
Elcometer Limited
Elcometer 122 Testex® Tape consists of foam with a non-compressible backing. The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile. The profile of the surface can then be measured using the Elcometer 124 Thickness Gauge.
-
134A -
Elcometer Limited
Contamination can build up, particularly if the blast media is recycled several times. Using the Elcometer 134A Chloride Ion Test in the field will accurately identify contamination and prevent costly surface-related failures.