Schwarzbeck Mess Elektronik
An international manufacturer of precision measurement technology, Schwarzbeck has own laboratory facilities to calibrate a variety of instruments, antennas and measurement equipment of EMC and RF technology.
- +49 (0) 6228 / 1001
- +49 (0) 6228 / 1003
- office@schwarzbeck.de
- Ziegelhäuser Straße 25
Schönau, D - 69250
Germany
-
product
3-Dimensional Loop Antenna Van Veen
Loop Antenna System ( LAS )3-dimensional large loop antennadiam. 2 macc. EN 55015 / CISPR 15
-
product
Absorbing Clamps
The Absorbing Clamp was designed to measure the disturbance power according to CISPR 16-2-2 in the frequency range 30-1000 MHz, it complies to the technical requirements of CISPR 16-1-3.
-
product
Active Antennas
Is an antenna that contains active electronic components such as transistors, as opposed to most antennas which only consist of passive components such as metal rods, capacitors and inductors.
-
product
Active Loop Antennas / Magnetic Field Probes
Is an active, shielded handheld loop antenna with nearly con- stant antenna factor over the entire frequency range. It can be used for testing according to CISPR, MIL, FCC, EN, ISO, ANSI, ETSI and many other standards.
-
product
Antenna Holders / Baluns
They are vital components in radio antenna systems. They enable the conversion of a balanced signal to an unbalanced one, ensuring optimal communication between the antenna and the radio.
-
product
Antenna Impedance Converter
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
product
Antennas
Is a specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
product
Attenuators And Pulse Limiters
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
product
Automotive Antennas
Are critical components in vehicles, serving various communication and entertainment purposes. automotive antenna come in different types and designs, each suited to specific functions and technologies.
-
product
Baluns
Causes a voltage transformation Uin / Uout = 1 / 2 and is designed for operation with hand- held field coil when performing tests.
-
product
Battery Simulator
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
product
Biconical Antennas
Biconical Antennas have dipole like characteristics (e.g. circular directional pattern in the H-plane,"8"-shaped in the E-plane, fixed phase center, comparable gain), with an enormous wide bandwidth achieved by the double cone elements.
-
product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength ...show more -
product
Biconic Logarithmic Periodic Antennas (Hybrid)
It combines the electrical properties of two antenna (biconical and Log ).
-
product
Broadband Horn Antennas
Offer a very low SWR in their nominal frequency range and a very broad bandwidth. The increasing gain with frequency helps to compensate cable losses. Is suitable for both, transmission and receiving applications. The max. allowed Input Power is only limited by the coaxial connector.
