Noisecom
A tradename of Wireless Telecom Group, Inc., a global provider of RF and microwave based noise and test equipment solutions for the telecommunications industry.
- 973 386 9696
- 973 386 9191
- info@noisecom.com
- 25 Eastmans Road
Parsippany, New Jersey 07054-3702
United States
Filter Results By:
Products
Applications
-
product
Jitter Noise Generator
J7000
The J7000A Series instruments high crest factor output is used as a random jitter source for serial data bus applications, including PCI Express Gen I & II, Serial ATA, and Fiber Channel. The noise source is designed for the PCI-SIG total jitter (Tj) model serial data application, but can be used for any random jitter noise application.
-
product
NBS-Series Cryogenic Primary Noise Standards
The NBS-Series provide the ultimate accuracy when measuring extremely low noise figures (noise temperatures).
-
product
Noise Generator
UFX7000
The UFX7000A Series instruments provide Broadband Gaussian noise with superior flatness. The output power can be attenuated up to 127 dB in 1 dB steps, and several connector types are available.
-
product
Noise Generator
CNG-EbNo SNR
The UFX-EbNo is a fully automated precision signal to noise generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal power meter provides repeatable SNR waveforms for accurate signal generation.
-
product
Broadband
NC346 Series
Noisecom's NC346 Series is designed for Broadband coaxial noise figure measurement applications. Each module's low VSWR reduces reflections and increases measurement accuracy.
-
product
Broadband Amplified Noise Modules
NC2000/4000 Series
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
product
Coaxial
NC3000
The NC 3000 Series calibrated coaxial noise sources are well suited for receiver testing, noise figure measurements, or applications that require broadband noise and fast switching times.
-
product
Analog Noise Generator
PNG7000
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
product
Noise & Interference Generator
GPS7500
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
-
product
Amplified Noise Modules
NC1000 Series
The NC1000 Series amplified noise modules produce AWGN as high as +13 dBm, and have bandwidths up to 10 GHz. The high power modules are designed to test noise immunity for Cable TV equipment, secure communication channels, and military jamming systems. The lower power modules, <= 0 dBm, are random jitter sources for many applications including, PCIexpress, Infiniband, and 10 GigE.
-
product
60 GHz Noise Figure Test Set
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
product
Chips and Diodes
NC100/200/300/400 Series
Noisecom's noise diodes are the fundamental building blocks for analog noise systems. They are sorted for performance characteristics that enhance their broadband noise output and flat spectral response. All Noisecom noise diodes can deliver symmetrical white Gaussian noise and flat output power versus frequency
-
product
Waveguide
NC346
The NC346 Series waveguide is designed for narrow-band high ENR noise figure measurement applications. For high power waveguide systems the series has an optional built-in isolator to provides very low VSWR and superior flatness, typically <= +/- 1.5 dB.
-
product
SNR Noise Generator
CNG-EbNo
The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signals are used to compare theoretical BER to SNR ratios, found in "waterfall" type graphs, with measured values from the DUT to evaluate different modulation schemes. Users can obtain higher yield through automated testing, plus increased confidence from repeatable, accurate test results. Standard units can be modified for specific customer requirements. Please consult the factory for pricing and availability of these requests.
-
product
High ENR Coaxial
NC3400
The NC3400 Series coaxial noise sources are an excellent choice for applications requiring high ENR and immunity to large incident RF power, such as ATE, radiometer, and radar systems
Parent
-
Wireless Telecom Group, Inc.
Setting the highest standards in accuracy and ease-of-use, Boonton Electronics ("Boonton") is recognized as a leader in high-performance test instrumentation and sensors. We are a manufacturer of test equipment dedicated to measuring the power of RF and microwave systems used in both military and commercial sectors. The company also manufactures impedance measuring instruments, RF voltmeters and audio analyzers.
Siblings
-
Boonton Electronics
Setting the highest standards in accuracy and ease-of-use, Boonton Electronics ("Boonton") is recognized as a leader in high-performance test instrumentation and sensors. We are a manufacturer of test equipment dedicated to measuring the power of RF and microwave systems used in both military and commercial sectors. The company also manufactures impedance measuring instruments, RF voltmeters and audio analyzers. Boonton Electronics is a wholly owned subsidary of Wireless Telecom Group Inc.
Siblings
-
Microlab
Microlab, A Wireless Telecom Group Company, founded in 1949, designs and manufactures high-performance passive RF and Microwave components such as dividers, directional couplers and filters.
Siblings
-
CommAgility Limited
Leading manufacturer of signal processing AMC modules for wireless baseband applications, combining flexible antenna interfaces, the latest TI DSPs and Xilinx FPGAs, and high bandwidth on and off-card communications using Serial RapidIO and Ethernet.
Siblings
-
Holzworth Instrumentation, Inc.
A global provider of ultra low phase noise RF Synthesizers, Phase Noise Test Systems and Components...
