Showing results: 76 - 90 of 105 items found.
-
115250 -
ICS Electronics
* C-Size blank PC Board for mounting devices, modules or circuits.* Includes VXIbus P1 and P2 connectors and decoupled power pads.* Includes pads for all VXI bus signals.* Includes pad patterns for common front panel connectors, LEDs, and a Reset Switch.* Includes CAD Design aids for Schematic Capture, PC board layout and front panel machining.* Use with ICS 1, 2 and 3-slot wide Module Shield Kits to create a complete enclosed module.* Use with ICS Front Panel Kits to add a front panel and ejectors to the blank board.
-
ICS Electronics
* Single-slot wide front panel is a bend resistant, aluminum extrusion with mounting holes and ejector slots.* Ejector handles have removable face plates for labeling the module.* Kit includes ejector handles, mounting hardware, one blank face plate, one face plate with VXI logo, and assembly screws.* Layout drawings and CAD design aids available for adding additional cutouts to the blank panels.
-
ICS Electronics
*Enclose any VXI module with these one, two and three slot-wide kits. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
ICS Electronics
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
ICS Electronics
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
VXI-5524A-3 -
ICS Electronics
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
ICS Electronics
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
Model 4861B OEM -
ICS Electronics
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Model 4804B-7 -
ICS Electronics
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Model 2399 -
ICS Electronics
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
Model 4863 OEM -
ICS Electronics
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
VXI-5524A -
ICS Electronics
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
ICS Electronics
Designed for legacy systems where there is a need to replace older X3.28 protocol Controllers and with new Modbus RTU Controllers. The Model 2399 provides ANSI X3.28 to Modbus RTU Conversion without changing the existing system software. The 2399 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands when controlling Modbus RTU devices.
-
Model 2390 -
ICS Electronics
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
ICS Electronics
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.