Showing results: 16 - 30 of 102 items found.
-
IP-429 -
Dynamic Engineering
ARINC 429 is a versatile standardized bus interface. ARINC 429 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates. ARINC 429 is the interface of choice for critical applications; for example aircraft instrumentation and control.
-
Dynamic Engineering
The Industry Pack mounting hardware kit provides the necessary hardware to mount an IP board to a carrier board.
-
Dynamic Engineering
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
Dynamic Engineering
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
Dynamic Engineering
IndustryPack compatible IP-Parallel-IO with counter and timer design adds up to 48 digital parallel IO lines to one IP slot of your carrier board.
-
Dynamic Engineering
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
Dynamic Engineering
IP Compatible card with 4 programmable pulse generators. TTL or RS422 / RS485 compatible outputs. Programmable pulse - nS to seconds. Programmable count or free
-
Dynamic Engineering
IP Module with quad UART capability. 128 byte FIFOs, 8 & 32 MHz operation, RS232 and RS422/RS485 interface, programmable terminations, 1.5MHz - 100 Hz.
-
Dynamic Engineering
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
Dynamic Engineering
Each IP-ReflectiveMemory can be used as a standard node or as the Master Node. Clearly labled "DIP Switches" are provided to make the selection of Master or Standard Node, and the Node Address. The Network is based on using LVDS signaling over Ethernet cabling. Nodes automatically come up for pass through operation.
-
IP-Crypto -
Dynamic Engineering
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
Dynamic Engineering
The PC104p Chassis comes in two base sizes : 5 slots or 10 slots. The two models are adaptable to allow 1,2,3,4, or 5 cards to be mounted in the 5 slot unit and any number up to 10 in the larger unit. In a typical system the first position in the stack would be the power supply, the second the CPU and the rest IO or storage
-
PC/104p-BiSerial -
Dynamic Engineering
The PC/104p BiSerial has been ported from the PMC BiSerial II. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PC/104p--BiSerial. The BiSerial features completely isolated FIFOs with 32 bit ports for increased adaptability and performance
-
PC104p2PMC -
Dynamic Engineering
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
-
PCI2cPCI -
Dynamic Engineering
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.