Showing results: 76 - 90 of 102 items found.
-
IP-1553 -
Dynamic Engineering
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
Dynamic Engineering
The Cable Assembly Crypto / Tape provides a method of interconnecting the IP-Crypto and IP-Tape from the carrier to the PCI Bezel [rear IO] when installed into a PCI machine. Most IP Carriers have 50 pin headers suitable for ribbon cable in use for the IP Module IO. The headers are located on the carrier and internal to the chassis. Interconnecting to the outside world can be an issue.
-
PMC-Wizard -
Dynamic Engineering
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
PMC-SpaceWire -
Dynamic Engineering
Utilize SpaceWire to communicate with the European Space Agency and NASA equipment utilizing the ECSS-E-50-12A specification. SpaceWire is configured using routers to create a heirarchical point-to-point system with high speed parallel paths. PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues.
-
Dynamic Engineering
The PIM-Parallel-IO facilitates rear panel IO in cPCI based systems using PMC's. The PIM-Parallel-IO provides the PMC_Parallel_IO front panel IO where rear panel IO is desired. The PIM-Parallel-IO can be used with other PMCs as well.
-
PCI5IP -
Dynamic Engineering
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
PCIe4LXMCX1 -
Dynamic Engineering
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
PCIe-Harpoon -
Dynamic Engineering
PCIe-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCIe-Harpoon is to simulate - act as if the PCIe-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCIe-Harpoon can provide status and direct software control of the system.
-
PC104p4IP -
Dynamic Engineering
If you want to use IndustryPack modules with your PC/104+ or PC/104-Plus system, the PC104p4IP is the choice for you. The PC104p4IP combines features you need with simplicity and speed. Up to 4 IP modules can be installed. Standard 16 bit IPs plus 32 bit, and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection. The PC104p4IP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA.
-
PCIe3IP -
Dynamic Engineering
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
PCI - HARPOON -
Dynamic Engineering
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
Dynamic Engineering
Peripheral Component Interconnect Express or PCIe, PCIexpress etc. is a serial interconnect system with bidirectional, and potentially parallel traffic at high speeds. Signalling is encoded for error checking and line loading. There are 3 "Gens" fairly widely in use at this time.
-
Dynamic Engineering
The PMC compatible PMC-Parallel-485 design adds 32 [RS-485 /RS-422] differential IO lines to one slot of your carrier board. 2 additional differential pairs are available for a clock & clock enable. The signals can be used to capture data with an external reference or programmed to be references for the rest of the system.
-
IP-Debug-Bus -
Dynamic Engineering
IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification
-
PC104pIP -
Dynamic Engineering
If you want to use IndustryPack modules with your PC/104+ system then the PC104pIP is the choice for you. The PC104pIP combines features you need with simplicity and speed. One IP module can be installed per carrier. Multiple carriers can be used in a stack. The PC104pIP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA