Showing results: 76 - 90 of 265 items found.
-
AR2 -
North Atlantic Industries
The AR2 module provides an ARINC 568/579 communications interface with 2 channels. Channel 1 is Rx and Tx for ARINC 568 and channel 2 is programmable as either Rx or Tx for ARINC 579. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer.
-
FTK -
North Atlantic Industries
Based on the MIL-STD-1553 signal and interface backbone, MIL-STD-1760 defines a standardized electrical interface to address additional aircraft weapons stores management and as such, includes some special requirements. The FTK module meets the operational requirements within the general specifications of MIL-STD-1760 as applied to an integrated I/O function module, and include special designed holt transceivers to ensure signal parameter operation and integrity.
-
FTE -
North Atlantic Industries
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
FTB -
North Atlantic Industries
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
56RS3 -
North Atlantic Industries
NAI’s 56RS3 is a 300 Watt AC/DC Power Supply that accepts a three-phase, AC input plus a +270 VDC input. This COTS unit provides a single full-power output (300 Watts) at a baseplate temperature of +85° C or a single 350 Watt output at a baseplate temperature of +70° C.
-
44PA1 -
North Atlantic Industries
The 44PA1 is a military grade Synchro Booster Amplifier that delivers 30 VA over the frequency range of 47 Hz to 10 kHz and will drive most CTs or TRs. It is transformer isolated, short circuit protected, and provides an accuracy of up to ±3 arc minutes.
-
75ARM1 -
North Atlantic Industries
NAI’s 75ARM1 is a 3U cPCI ARM® Cortex®-A9-based, Single Board Computer (SBC) that can be configured with up to three intelligent function modules. Ideally suited for rugged defense, industrial, and commercial applications, the 75ARM1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
75C3 -
North Atlantic Industries
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
3U cPCI 75C5 -
North Atlantic Industries
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
75D4-H2 -
North Atlantic Industries
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
75G5 -
North Atlantic Industries
NAI's latest generation 3U cPCI Multifunction I/O and Communication Board, the 75G5, can be configured with up to three smart function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
75PPC1 -
North Atlantic Industries
NAI’s 75PPC1 is a 3U cPCI NXP® QorIQ® P2041, PowerPC-based, Single Board Computer (SBC) that can be configured with up to two intelligent function modules. Ideally suited for rugged defense, industrial, and commercial applications, the 75PPC1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
75SBC4 -
North Atlantic Industries
NAI’s 75SBC4 is a 3U cPCI NXP™ QorIQ® P2041, PowerPC-based, Single Board Computer (SBC) with dual, high-speed/high-performance function module slots for configurable multifunction I/O interface expansion. Ideally suited for rugged defense, industrial, and commercial applications, this low-power, cost-conscious, SBC delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
75DS2 -
North Atlantic Industries
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
68CB6 -
North Atlantic Industries
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
