ABex Accessories
ABex Accessories by Konrad
- Analog Bus Extension for PXI
- ABex Accessories
- ABEX Base Devices
- ABex Chassis
- ABex Modules
- PXI Modules
- ABex Software
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
16 Channel 12C Relay Expansion
FXA-105 I2C Relay 16CH
The FXA-105 provides sixteen I2C controlled relays. It is equipped with a wide range 7V to 24V power supply and based on a 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
19" Breakout & Power Input Panel
Cabinet CP-103
The CP-103 is breakout and power input panel which is used to provide a clear connection interface for 19” racks. It is equipped with the most common interfaces found on industrial computers. In addition, it provides a single phase 16A CEE connector and a brush to feed through additional cables and tubes. Furthermore, it’s M6 threaded plate installed to simplify equipotential bonding.
-
product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
product
19" Breakout Panel for Ethernet, USB & DisplayPort
Cabinet CP-101 & CP-102
The CP-101 & CP102 are breakout panels which are used to provide a clear connection interface for 19” racks. They are equipped with the most common interfaces found on industrial computers. Both variants feature the same connectors, but distinguish in cable length (1m for CP-101 and 2m for CP-102).
-
product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
16 Channel 12C Relay Expansion
FXA-105 I2C Relay 16CH
The FXA-105 provides sixteen I2C controlled relays. It is equipped with a wide range 7V to 24V power supply and based on a 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
19" Breakout & Power Input Panel
Cabinet CP-103
The CP-103 is breakout and power input panel which is used to provide a clear connection interface for 19” racks. It is equipped with the most common interfaces found on industrial computers. In addition, it provides a single phase 16A CEE connector and a brush to feed through additional cables and tubes. Furthermore, it’s M6 threaded plate installed to simplify equipotential bonding.
-
product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
product
19" Breakout Panel for Ethernet, USB & DisplayPort
Cabinet CP-101 & CP-102
The CP-101 & CP102 are breakout panels which are used to provide a clear connection interface for 19” racks. They are equipped with the most common interfaces found on industrial computers. Both variants feature the same connectors, but distinguish in cable length (1m for CP-101 and 2m for CP-102).
-
product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
