-
product
(2×32)-Ch 1A-1500VDC 24VAC Matrix
YAV90097
32-Lines selectable High-Open-Low connection 3kV 1,0A Relays (Cool connection) Hipot test capabilities CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(4×30)-Ch 3A-250VAC 24VDC Matrix
YAV90120
120 relays SPST matrix 4×30 3Amps 1wire Max switching up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×16)-Ch 2A-250VAC 24VDC Matrix
YAV90069
Software configurable for: 1(64×2), 2(32×2), 1(16×2) + 3(16×2). Switching 2A 250Vac. Max switching up to 62.5V CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×16)-Ch Dual Pole 2A-250VAC Matrix
YAV90060
128 relays DPST double matrix (4×16). Switching up to 250Vac and 2A CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×32)-Ch 0,5A-200VAC Matrix
YAV90062
256 relays SPST matrix (4×64 1 pole) or (4×32 2 poles). Max switching 10W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
10Ch Electronic Potentiometer 8 Bit
YAV90084
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
product
Potentiometer Module
YAV90084A
4x 8-Bit 1KOhm reostat 4x 8-Bit 40 Ohm reostat 2x 8-Bit 5 MOhm reostat 10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in selft test. 10x Voltage to current source 0(4)..20mA 10x Analog Outputs (Buffer for voltage or frequency) 36-Ch Test Point voltage divider 2xCAN Bus Channels Terminators tester Expandable with NI PXI-6723 and PXI-6345.
-
product
96-Ch Switching
YAV90064
96 relays SPST, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
96 Sink/Source
YAV90096
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
product
80 I/O Multifunction Module
YAV90832
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Boundary Scan Resources Unit Expantion
YAV9JTAH
80 DIOs 8 Ais 8 AOs Compatible with all JTAG vendors
-
product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Industrial Programmers Interface up to 8 targets. Relay Barrier Demultiplexer module up to 32 devices. Communication Interfaces I2C and SPI.
-
product
64-Ch 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
48-Ch Switching
YAV91074
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
48 Optocoupled Digital Inputs
YAV90321
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
32-Ch Switching
YAV90132
32 relays, 5A 28 SPDT relays, 5A Mux. 1 a 4 relays CAN Control or Ethernet (with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
32-Ch Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
32-Ch Multimeter
YAV90HVT
32 relays High Voltage (Up to 1500V) Multimeter/Amperimeter 14 bits resolution. 1x Analog Output and 2x Digital Outputs Internal automatic calibration CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available Automatic module identifier
-
product
24Vdc Module
YAV90304
8 x 24Vdc PNP Inputs 16 x 24Vdc 600mA PNP Outputs CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
16-Ch SPST 10A-277VAC High Current
YAV90086
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
High Current Power Switching
YAV90CIN
12 Independent SPST relays Switching up to 8A 250Vac 12 current measurement channels 8x Sense connections General inhibit input CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
High Current Power Switching
YAV90PIN
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
10-Ch Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
4x IDC Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
-
product
48-Ch Bus Fault Insertion
YAV90076
48 channels 2A 250V 2 Fault Insertion Buses Switching up to 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
-
product
Ethernet to CAN Bus Gateway
YAV90090
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
(2×32)-Ch 1A-1500VDC 24VAC Matrix
YAV90097
32-Lines selectable High-Open-Low connection 3kV 1,0A Relays (Cool connection) Hipot test capabilities CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(4×30)-Ch 3A-250VAC 24VDC Matrix
YAV90120
120 relays SPST matrix 4×30 3Amps 1wire Max switching up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×16)-Ch 2A-250VAC 24VDC Matrix
YAV90069
Software configurable for: 1(64×2), 2(32×2), 1(16×2) + 3(16×2). Switching 2A 250Vac. Max switching up to 62.5V CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×16)-Ch Dual Pole 2A-250VAC Matrix
YAV90060
128 relays DPST double matrix (4×16). Switching up to 250Vac and 2A CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
(8×32)-Ch 0,5A-200VAC Matrix
YAV90062
256 relays SPST matrix (4×64 1 pole) or (4×32 2 poles). Max switching 10W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
16-Ch SPST 10A-277VAC High Current
YAV90086
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
96-Ch Switching
YAV90064
96 relays SPST, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
High Current Power Switching
YAV90CIN
12 Independent SPST relays Switching up to 8A 250Vac 12 current measurement channels 8x Sense connections General inhibit input CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
10-Ch Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
10Ch Electronic Potentiometer 8 Bit
YAV90084
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
24Vdc Module
YAV90304
8 x 24Vdc PNP Inputs 16 x 24Vdc 600mA PNP Outputs CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
32-Ch Multimeter
YAV90HVT
32 relays High Voltage (Up to 1500V) Multimeter/Amperimeter 14 bits resolution. 1x Analog Output and 2x Digital Outputs Internal automatic calibration CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available Automatic module identifier
-
product
32-Ch Switching
YAV90132
32 relays, 5A 28 SPDT relays, 5A Mux. 1 a 4 relays CAN Control or Ethernet (with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
32-Ch Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
48 Optocoupled Digital Inputs
YAV90321
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
48-Ch Bus Fault Insertion
YAV90076
48 channels 2A 250V 2 Fault Insertion Buses Switching up to 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
48-Ch Switching
YAV91074
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
-
product
64-Ch 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Industrial Programmers Interface up to 8 targets. Relay Barrier Demultiplexer module up to 32 devices. Communication Interfaces I2C and SPI.
-
product
80 I/O Multifunction Module
YAV90832
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
