Breakout Boards
"Breaks out" these pins onto a printed circuit board that has its own pins that are spaced perfectly for a solderless breadboard, giving you easy access to use the integrated circuit.
-
product
Accelerometor, Gyro, Magnetometer Breakout Board
SEN-38001
The LSM9DS1 is a highly configurable, flexible and precise motion sensing solution from ST Microelectronics - the latest in a wide-ranging inertial product line. It integrates a 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer into a single IC , giving you a full nine degrees of freedom (9-DOF) in a tiny 3mm x 3.5mm package. Even with support components, square mounting pattern and connection breakouts for both SPI and I2C, this board is barely the size of a quarter.
-
product
Bi-Directional Level Translator
IFB-10001
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
product
Dual MAX31865 PT-1000 RTD to Digital Breakout
SEN-30202-PT1K
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information.
-
product
HUSKIE 2.0 roboRIO MXP Expansion Board
FRC3061-MXP2-R1
The Huskie Board, designed by FRC Team 3061, is an FRC qualified expansion board for the NI roboRIO robotics controller. In addition to breaking out all available signals on the MXP expansion port, this board uses a Parallax Propeller IC (8 symmetrical logical cores with shared memory and peripheral access) to enable tasks such as advanced data logging, on-field driver control and status, and NeoPixel control. Additional GPIO and analog inputs are added with open source code to allow further customization.
-
product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-J
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
