Showing results: 691 - 705 of 3061 items found.
-
BD300 -
Shanghai Baudcom Communication Device Co.,Ltd.
BD300 Optical Time Domain Reflectometerhas excellent dead zone performance and wide dynamic range. Combined with the visualfault locator, the OTDR can easily find the breaks, bends, splices, faultyconnectors, and other causes of signal loss.
-
DCM-G.652-C-Fxx -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai and DCM-G.652-C-Fxx dispersion compensation fiber module, is negative dispersion compensation based on optical fiber technology, can effectively compensate for G.652 standard single-mode fiber transmission band of 1525 ~ 1565nm dispersion and dispersion slope characteristic.
-
H9925 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9925 is a type of bi-directional optical receiver with high performance, low cost and economical. It is applicable to various application of the HFC network fiber to the home (FTTH), and can provide high reliability analogue, digital video frequency and data bi-directional transmission for the HFC network.
-
CA92001B -
UC Instruments, Corp.
UCINSTRUMENTS CA92001B C band optical spectrum analyzer module is a spectral engine for Process Analytical Technology applications. The OSA module acts as a stand-alone spectral engine, imaging and measuring a wide range of vapors, liquids and solids through transmission and diffuse reflection in a rapid non-destructive process. Leveraging our proprietary Micro-Optic technology, UC INSTRUMENTS’ C band OSA module features the following characteristics: (1) compact; (2) light-weight; (3) low power consumption; and (4) wide wavelength coverage. These characteristics of UC INSTRUMENTS’ compact OSA engines are suitable for a variety of handheld, portable or bench-top OSA/spectrometer applications. Equipped with a state-of-the-art internal wavelength reference, the OSA module is capable of precisely measuring optical spectrum. Because it does not require an expensive InGaAs detector array, the compact OSA module is a cost-effective alternative to other grating-based OSA/spectrometer engines. The OSA communicates with a PC or an instrument motherboard via an USB interface. UCINSTRUMENTS’ OSA module platform can be installed or co-packaged into existing NIR OSA/spectrometers as a cost-efficient alternative to other scanning optical engines.
-
N7752A -
Keysight Technologies
The Keysight N7752A combines an attenuator with 2 front-panel power meter channels, offering exceptional performance at a low price. The power meters permit measurements from any point in the measurements setup and assist in calibrating power offsets with respect to the attenuator output.
-
Power 1600 Series -
Quantifi Photonics Inc.
Quantifi Photonics’ Power 1600 Series inline optical power meters provides quick and accurate inline power monitoring.Seamlessly integrate the power meter into your new or existing PXI test setup and save space, lower your costs and improve testing efficiency.
-
KI27624-INGAAS-APC -
Kingfisher International
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Optical Wavelength Laboratories
Features include: user-definable optical power threshold, selectable channel spacing (50 & 100 GHz), and data storage.Data can be viewed either as a bar graph or in tabular format, and the LCD display will automatically rotate based on the orientation of the OCM unit. Viewing in landscape mode allows for more viewing detail.
-
Torontech Group
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
IF-SensorR25 -
Alicona Imaging GmbH
The IF-Sensor25 is a solid optical 3D measurement instrument for automated form and roughness measurement in production. The sensor is integrated into a production line and delivers you high resolution, repeatable and traceable results when measuring surface characteristics in the m or sub-m range. This resolution can hardly be achieved by conventional 2D solutions or tactile techniques.
-
BG9244x-LE -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BG9244 is a type of out-door optical receiver . The product builds-in RF interstage gain adjustment and equalization. Users can choose one-way or two-way high output level with the insert. The product is used in FTTB, FTTN, FTTC and used as a Rx unit of CATV. It is a type of receiver with high flexibility, excellent performance and P/P ratio.
-
METRASCAN-R -
Creaform Inc.
Part of the MetraSCAN 3D line-up, the robot-mounted MetraSCAN-R optical CMM 3D scanning systems are fast and accurate scanning solutions designed for 3D automated inspection of parts on the production line and on the shop floor. In combination with industrial robots, the MetraSCAN-R series increases the reliability, speed and versatility of on-line inspection and quality control (QC) process.
-
FOMA -
Radiantech, Inc.
FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
dOCTor™ -
NOVACAM Technologies, Inc.
dOCTor™ Optical Coherence Tomography (OCT) systemsoffer very high quality non-invasive tissue imaging in 2D and 3D. They are ideal for: In-Vivo Imaging Small Animal Imaging Tissue Engineering and Visualization Developmental BiologydOCTor systems are available in Swept-Source(SS) OCT and Time-Domain (TD) OCT configurations to satisfy different application imaging needs.
-
M2 Optics, Inc.
The Remote Fiber Monitoring System offered by M2 Optics is a key asset for any network operator seeking to ensure the performance and integrity of the optical fiber infrastructure. In addition to significantly reducing service times to meet customer service and SLA requirements, the system provides an extra level of intrusion detection against the serious threat of malicious data theft affecting today's networks.