Filter Results By:
Products
Applications
Manufacturers
Meters
sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.
See Also: Sensors, Measurement
-
-
product
Covermeters & Half-Cell Meters
331
The Elcometer 331 is an all in one gauge that combines the rebar locator, concrete covermeter and half-cell measurement, making site visits quicker and more convenient.
-
product
Dewpoint Meter
319
A hand-held dewpoint meter with both manual and automatic data logging in one gaugeIntegrated magnets allow the dew point gauge to be attached to the substrate during remote loggingStores 25,000 records in up to 999 batchesDustproof and waterproof gauge with fully sealed sensors (equivalent to IP66)Gauges can be recertified at Elcometer Authorised Service CentresRobust temperature sensorsEasy to use, intuitive menu structureMeasure and record climatic parameters:Relative humidityAir temperatureSurface temperatureDewpoint temperatureTΔ (the difference between surface temperature and dewpoint)Dry Bulb temperatureWet Bulb temperatureExternal temperature correction (K-type)Specific HumidityVisual and audible indication of user defined limits for any or all parametersUSB and Bluetooth® data output to ElcoMaster® software
-
product
Automotive Paint Meter
311
The Elcometer 311 Automotive Paint Meter allows the user to quickly identify vehicle’s damage not reported in public or commercial condition reports including:hidden reworkvehicle impact damagevehicle resprayfilled body panels
-
product
Concrete Moisture Meter
7410
The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.Calibrated ready for use on concreteInstant readings on a clear, easy to read scaleFully portable, battery operated and non-destructive
-
product
Gloss & Reflectance
Visual appearance can determine a person’s perception of a product. Colour and Gloss are two key parameters that are used to define a product’s overall quality. Perception is subjective, but Elcometer’s range of gloss meters, DOI meters and colour assessment equipment can quantify appearance measurement. The ability of a surface to reflect light without scattering is known as gloss. Using a gloss meter, gloss is measured by directing a constant intensity light beam at a fixed angle to the test surface and then by monitoring the amount of reflected light at the same angle. Different surfaces require different reflective angles.
-
product
Bresle Salt Kit
138
The Elcometer 138 Bresle Kit includes the Elcometer 138 Conductivity Meter. This lightweight, portable conductivity meter accurately measures the salinity of the test samples.The cartridge type sensor can be easily replaced when necessary and displays conductivity in a range of units including: S/cm, S/m, ppm and % salinity.
-
product
Bresle Salt Meter
Elcometer 138
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
product
Digital Moisture Meter
7000
Available in two versions, the Concrete Moisture Meter has a non-invasive probe that emits a radio frequency to penetrate the surface to detect moisture. Ideal for rapid surveys of solid wall, floors and ceramic tiles. The Digital Moisture Meter has two pin probes that allow the gauge to be pressed on to a surface and take a measurement of the immediate area and also has a non-invasive probe on the back of the gauge for moisture detection.
-
product
Covermeter & Half-Cell Meters
A covermeter, or rebar locator, is a gauge that measures the thickness of concrete cover over steel reinforcement bars and metal pipes. The covermeter can tell you the depth of the rebar, the location and orientation of reinforcement bar (rebar) and determine the diameter of the rebar.
-
product
Concrete Inspection
Concrete structures are normally constructed using steel reinforcement and Elcometer offers Concrete Covermeters and Rebar Locators to either measure the depth of concrete over the rebar or simply to detect the rebar under the surface. Half-cell versions of the Covermeter can be used to assess the probability that corrosion is taking place on the rebar. Test Hammers are used to assess the surface hardness of cured concrete and Elcometer offers several moisture meters that can be used to determine if the structure is sufficiently dry for coating.
-
product
Half-Cell Meter
331HM
These easy to use Elcometer 331 Half-Cell Meters measure the condition and potential corrosion of rebars and steel structures within concrete.
-
product
Salt Contamination Meter
130
Key features of the Elcometer 130 Salt Contamination Meter include: Fast reading rate allows multiple conductivity tests to be completed efficiently Pressure plate ensures a constant and uniform pressure to paper Automatic detection of paper size and automatic adjustment of reading value USB and Bluetooth® data output to ElcoMaster® software Dust and water resistant rugged design equivalent to IP64 Automatic temperature compensation ensures accurate results Non-oxidising gold plated contacts ensures lifetime accuracy Stores up to 150,000 readings in 2,500 alpha numeric batches Fully portable hand-held, ergonomic design ideal for use in the field
-
product
Moisture Measurement
Moisture: The presence of moisture within a material will result in poor adhesion, premature coating failure and poor appearance. For example, applying a powder coating to a damp wooden panel will cause steam to be created when the panel passes through the curing oven, thus causing damage to the coating. It is not sufficient to simply ensure that the surface is dry by touch. The surface of the substrate is often the driest point due to evaporation. It is important to establish the moisture content within the substrate itself. The moisture measurement can either be taken using a Pin moisture meter or Pinless (Contact-Type) moisture meter.
-
-
-
product
USB Digital Meters
Klein Tools’ USB testers accurately and reliably measure USB port voltage, current, capacity, energy and resistance simultaneously. As they require no batteries, these tools are easy to keep in a tool bag and quickly pull out anytime a USB port needs to be measured.
-
product
Clamp Meters
Klein Tools' line of clamp meters is designed to give professionals increased accuracy and easy to read results regardless of what the job requires. These meters are built to stand up to tough jobsite conditions and have been designed with specific trades in mind.
-
product
Pulser Sensor, Sent Signal, CNEX/ATEX Certificates
SK-S
Beijing SANKI Petroleum Technology Co., Ltd.
*convert the mechanical transmission signal of flow meter into electrical pulse signal* send the electrical pulse signal to main-board to realize the metrology function of the flow meter
-
product
Flow Meter
SK-FM
Beijing SANKI Petroleum Technology Co., Ltd.
High-precision metering device FM-500 was independently developed and manufactured by SANKI Company based on advanced technologies from Europe and America as per international metering standards OIMLR117 and OIMLR118
-
product
Energy Meters
Energy meters play a crucial role in the control and management of energy, offering key information for improving energy efficiency. Energy meters enable the trading of electricity and billing processes for both end users and businesses. Through energy meters, monitoring and energy consumption optimization can be achieved.
-
product
Energy Meters
EM4T II
*Accuracy <0.5R according to EN 50463-2*Compliant with EN 50463:2017*Can be utilized with power supplies (24V and 110V DC nominal)*4 input channels for metering of both AC and DC signals of any existing traction network (600V DC to 3kV DC, 15kV AC 16,7Hz, 25kV AC 50Hz)
-
product
Energy Meters
DCBM 400 / 600
*Split concept for easy integration*Range of operation 150 to 1000 V DC*Two sizes: Imax 400 A and Imax 600 A*Bi-directional energy metering*Wide operating temperature range
-
product
Energy Meters
TEMA4G
*Accuracy < 0.5R according to EN 50463-2*Compliant with EN 50463:2017*4 input channels for metering of both AC and DC signals of any existing traction network (600V DC to 3kV DC, 15kV AC 16,7Hz, 25kV AC 50Hz)
-
product
Energy Meters
DCBM 100
*Voltage measurement 150 to 1000 V DC*Current range 80A*Bi-directional energy metering
-
product
Portable Dew Point Meter
HDPM
Hention Electrical Equipment Co., Ltd.
The dew point transmitter of HDPM with high performance of Finland Vaisala Company is adopted as the core measurement unit of the entire system, it integrates multiple up-to-date research achievement and proprietary technology in measurement of dew point, and it is equipped with precision sampling system for sample gas and intelligent digital processing display, and it is one of existing dew point measurement instruments with the most advanced technique and the most powerful function.
-
product
Dual-Channel, Tri-port per channel, for extended cabling up to 4.5 meters
FW2
The FW2 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
product
Extinction Ratio Meter
Shenzhen Golight Technology Co.,Ltd
The extinction ratio meter can achieve accurate measurement of up to 40dB PER dynamic range. The instrument is precisely controlled by micro-machines, which can quickly and accurately measure the extinction ratio, polarization angle and optical power of the polarization-maintaining device.
-
product
Degree of Polarization Meter
DOP-201
The DOP-201 measures and displays the Degree of Polarization (DOP) of a light source in real time on the front panel display. The instruments incorporates a patented maximum & minimum search technique that accurately measures both low and high DOP. This technique is superior to polarimeter-based methods that are inaccurate at low values of DOP as well as scrambler-based methods which are less accurate at high values of DOP.
