Showing results: 1231 - 1245 of 3724 items found.
-
ChenYang Technologies GmbH & Co. KG
DC voltage sensor/transducer works according to Linear PhotoelectricalIsolation and is designed for applications to measurement and monitoring of DC voltage. Theoutput signal (DC voltage or current) of this transducer is proportional to the input DC voltage.They are suitable for measurements and long time monitoring of DC voltages and can applied topower supply management, DC motor drivers, battery chargers and systems etc.
-
МЦММ1 -
Holding Informtest
The mezzanine module (mezzanine) МЦММ1 is designed to measure AC and DC voltage, AC and DC current, DC resistance and frequency of a periodic signal.
-
Shanghai MCP Corp
dual DC power supply / adjustable dc power supply dual / 30v lab power supply/30v 5a variable dc power supply
-
-
Metra 16S -
Metra Blansko a.s.
It is Analog Digital Multimeter which measures VAC, VDC, VAC+DC, Frequency, mA DC, mA (AC+DC), Resistance, continuity, Diode, Farad, AC current measurement.
-
DCFlex -
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
-
GECC 3000 / 1500 -
Altanova Group
The DC voltage power supply models GECC3000 and GECC 1500 are designed for supplying the DC voltage and current for testing any type of system which requires an high-power, ripple free DC power supply
-
EM4T II -
LEM
*Accuracy <0.5R according to EN 50463-2*Compliant with EN 50463:2017*Can be utilized with power supplies (24V and 110V DC nominal)*4 input channels for metering of both AC and DC signals of any existing traction network (600V DC to 3kV DC, 15kV AC 16,7Hz, 25kV AC 50Hz)
-
Carl E. Holmes Company
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
VC-2 -
Tinker & Rasor
Portable, battery operatedHighly accurate DC outputVerify any DC VoltmeterBattery test LEDWorks with T&R
-
VECTOPOWER Family -
ARADEX AG
High-performance inverters and DC / DC converters for precise, safe and fast voltage regulation in electric drive systems.
-
Teledyne LeCroy
Voltage rail probes are designed specifically to probe a 50 Ohm DC power/voltage rail. The probe has large built-in offset, low attenuation (noise), and high DC input impedance. Built-in offset and low attenuation permit the power/voltage rail to be offset in the oscilloscope by its mean DC voltage with high oscilloscope gain (sensitivity) to achieve a noise-free view of small signal variations. The high DC input impedance eliminates loading of the DC rail.
-
Model 605A -
TREK, INC.
The Trek Model 605A is a high-voltage reference supply designed to provide precise control of output voltages in the range of 0 to +1 kV DC or 0 to -1 kV DC with an output current range of 0 to 1 mA DC.