HA
Measure nonsinusoidal waveform's amplitudes, frequencies and phases.
-
product
High Voltage Amplifier
HA-205
*2500V/uS Super High Speed Model *170Vp-p (±85V DC) *900mAp-p (±450mA DC) *Bandwidth: 3MHz / 100Vp-p *Gain (AMPL): 0~35 (10 Turn VR+SW) *Microprocess Control Protection
-
product
High Voltage Amplifier
HA-805
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
product
High Voltage Amplifier
HA-800
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
product
5mA High Accuracy Ground Fault Detector
HA-GFD
Our HA-GFD Current Probe is our most sensitive current probe, measuring down to 5 milliamps. Ideal for measuring leakage current and ground faults. Dual range allows measuring up to 200 amps in high accuracy.
-
product
With SAT-IF input EDFA
HA4600/IF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
product
High Voltage Amplifier
HA-405
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
product
wavefront sensors
HASO EUV
Imagine Optic's HASO EUV wavefront sensor, developed in conjunction with LOA and the SOLEIL synchrotron, is the only device of its kind available that offers you the extreme precision and direct measurement functionality needed for today's demanding laboratory and industrial applications.
-
product
PE/ Ground, Insulation Resistance Tester
Handheld
The safety testers of the Handheld class are used to measure PE/ Ground resistances, insulation resistances and to perform a simple functional test. The small and sturdy universal testers are intended for standard-compliant safety tests in workshops and production as well as for mobile operation during repair, installation, service and more.
-
product
Noise Monitoring System
Harmony
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
product
Test Handler
HA1200
The new HA1200 handler can be linked with a tester to utilize our unique active thermal control technology for testing singulated and/or partially assembled dies. This technology enables testing of powerful high-end SoCs with 100% test coverage. This helps reduce yield loss at final test, thus reducing losses of final multi-die assembled products.
-
product
Single Fiber Bi-Direction EDFA
HA8000
Hangzhou Huatai Optic Tech. Co., Ltd.
HA8000 series, is a bi-directional fiber amplifier with high-quality. It can transmit and amplify downlink and uplink signal on one fiber. It offers an economical solution to network operators when utilizing the existing fiber source, upgrading networks and providing bi-directional VAD business.
-
product
wavefront sensor
HASO3 FAST
Our HASO3 Fast Shack-Hartmann wavefront sensors provide fast accurate and reliable measurements by uniting the standard HASO family's standard functionalities that customers have come to rely on, including absolute measurement, unequalled accuracy and insensitivity to vibration, with an acquisition speed of 905 Hz and a spatial resolution of 14 x 14 microlenses.When coupled with our HASOv3 software package, you can perform both zonal and modal wavefront reconstruction; calculate the PSF*, MTF* and Strehl ratio*; visualize the spot diagram; and obtain the M* parameter. Adaptive optics users can take advantage of our CASAO software package to control adaptive optics loops to compensate for atmospheric turbulence, optimize the focal spots of laser beams and Freespace communications.
-
product
High Voltage Amplifier
HA-400
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
product
wavefront sensors
HASO4 FIRST
HASO4 FIRST is the ideal choice for results driven professionals in domains including adaptive optics, optical process optimization, laser beam characterization, and many others. Thanks to our patented technology, the HASO family by Imagine Optic are world's only sensors with no bias error, keeping its phase accuracy on any measured intensity profile (Gaussian, Top-Hat, hyper Gaussian, etc.). The USB 3.0 connectivity and the ergonomic design allow an easy plug and play installation of the HASO4 FIRST in any application.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400B (2RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400B (2RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400E (5RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400E (5RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
Multi-Wavelength Foresnic LED Light Source
HandScope LED
The only LED unit that changes and selects wavelengths like a forensic light source.
-
product
USB Oscilloscope
Handyprobe HP3
The Handyprobe HP3 is a small and light weight USB oscilloscope. The Handyprobe HP3 combines a fast sampling up to 100 MS/s with a high input range of 800 V and a differential input in a small and light enclosure. Powered only by USB, this verstatile USB scope enables safely measuring high voltages anywhere in the field. Its rugged housing is specially designed for use in a dirty and rough environment but is compact enough to fit into any tool case.
-
product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
product
Coordinate Measuring Machines
VideoCheck® HA
Fixed bridge CMM for highest precision and flexibilityIntegrated Werth Zoom® provides advanced capabilities for automatic measurement even for workpieces with minimal contrastIntegration of additional sensor units to a multisensor system guarantees higher flexibility and measuring speedModular structure guarantees customized solutions for individual applicationsOptional integration of a high precision air bearing rotary / rotary tilt axis
-
product
1000 Amp High Accuracy Current Probe
HA1000
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
product
Light Source
LS-HA
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
product
USB Oscilloscope
Handyscope HS6 DIFF
This powerful USB 3.0 super speed oscilloscope combines fast sampling up to 1 GS/s with high resolutions of 12, 14 and 16 bit and a large memory of 64 MSamples on all four channels. The oscilloscope supports continuous streaming measurements up to 200 MS/s and can be synchronized with other oscilloscopes using the CMI interface to form a multi channel combined instrument with synchronized timebase. The CMI interface is available by default on the Handyscope HS6 DIFF. Optionally, the Handyscope HS6 DIFF can be delivered with SureConnect connection test and resistance measurement on each channel. Also, the Handyscope HS6 DIFF can be delivered with SafeGround option. With SafeGround you can switch the differential inputs of the Handyscope HS6 DIFF into single ended inputs with ground protection. It allows to make measurements using standard attenuating probes and protects the scope when a short circuit to ground is created.
-
product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
product
CATV Line-Amplifier EDFA
HA5200
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5200 series C-Band line-amplifier EDFA (also knows as relay EDFA), is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Fiber CATV system operates generally in single wavelength that has no strict requirement on gain flatness. In order to reduce the effect of CNR deterioration caused by EDFA, input power should be as high as possible to make EDFA operate in saturated output power. The typical value of input power is >+3dBm.
-
product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
product
With CATV RF Input EDFA
HA4600/RF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400C (3RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400C (3RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
