Showing results: 271 - 285 of 595 items found.
-
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
19036 -
Chroma ATE Inc.
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
HopeTech
program-controlled safety tester includes CHT9910 / 9912/9922; it has AC / DC withstand voltage test and insulation resistance test function; it has 6 groups of test modes and can realize programmable test.AC / DC voltage output 10V ~ 5KV / 6KV, insulation resistance test range: 100KΩ ~ 99GΩ, meanwhile, it has arc detection and over power detection functions. Optional RS485 interface, you can easily experiment with instrument networking through MODBUS communication protocol.
-
M+P International
Vibration tests must be safe and reliable and this is especially true for high value specimens in critical aerospace testing applications. Here, m+p Coda offers maximum safety: The monitoring system captures and records data such as acceleration, temperature and strain continuously during vibration tests - irrespective of the vibration control system in use. Each channel can be configured separately for total flexibility.
-
SCR ELEKTRONIKS
SCR Elektroniks make Tumbling Barrel Apparatus is specially designed and manufactured for use in laboratories involved in testing Appliances, Electrical Accessories, Luminaries and other related Electro technical products. It is used to perform the test specified in many standards to determine compliance with safety requirements, particularly mechanical strength of test samples. SCR Elektroniks Makes Counter to count ON/OFF of Limit switch.
-
9801B Tester -
Hydraulic Technology, Inc.
The 9801B hydraulic hose tester is utilized by the U.S. Army for high pressure testing of hydraulic hose and tube assemblies as well as any component testing requiring test pressures up to 15,000 psi. Enhanced safety for operating personnel is achieved by utilizing the optional 8801HT integral test chamber which was designed specifically to fit to all our 8801B and 9801B testers.
-
VectorCAST/C++ -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing C/C++ software components necessary for validating safety- and mission-critical embedded systems.
-
IADS -
Curtiss-Wright Defense Solutions
IADS telemetry client software is the integrated display and analysis portion of the IADS data display, processing, delivery and archive software suite. IADS client facilitates real-time mission analysis and raises situational awareness, safety monitoring, and test point clearance capabilities to a new level.
-
SG-P11A -
Jinge Testing Machine Co.,Ltd
This machine, incorporating a steel striker adaptered to fall freely on vertical guides from a predetermined height to give the required impact energy to the toe of safety footwear for measuring the degree of the dent. In addition, the toecap should not develop any cracks on the test axis with go through the material.
-
Hilo Test
Hilo-Test manufactures power generators for surge current material and safety tests, in particular for the examination of diverting elements such as gas discharge tubes, varistors, SPDs, and components in which such protective elements are installed, according to according to the IEC / EN 61643-11. Below you will find the right solution.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Global Testing Services Inc.
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
EV-TEST100 -
HT Italia Srl
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
4105A -
Kingrun Instrument Co., Ltd.
• Dust and drip proof.(designed to IEC 529 IP54)• In addition to the facility for precision measurement, test leads for simplified two wire easuring system also supplied as standard accessories.(unit can be hung from the neck for simplified measurement)• Designed to meet IEC 61010-1 safety standard.