Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Safety Test Scanner
19200
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
product
Battery Test and Analysis System
BTAS-16
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
product
Circuit Breaker Test System
TDR9100
The Doble TDR9100 is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.The TDR9100 provides main contact timing, motion, resistance and capacitance measurements with the flexibility to double or triple your usable channels.Use this inclusive, rugged and field-portable instrument for simple and complex testing of circuit breakers.
-
product
Circuit Breaker Test System
TDR900
The TDR900 is your entry-level portable circuit breaker test set.It operates and records a circuit breaker's contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.Use the TDR900 to verify control circuit, check motion of moving parts, validate time of operation and demonstrate results of circuit breaker maintenance.
-
product
Laboratory Ozone Test Chamber
CX-150
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Complete Transformer Test Bench
Weshine Electric Manufacturing Co., Ltd
Our multifunction Transformer Test Bench (VS-ZHSY Series) is intuitive with all of the ease of working with individual, dedicated instruments. We deliver this experience through our design philosophy. Rather than producing a single, complex system with afterthought towards rendering it friendly, we uniquely combine several intelligent instruments packaged as a single system.
-
product
Diode & Rectifier Test Systems
D&V’s diode and rectifier test systems provide a quick, accurate and easy to use interface to check and measure all main parameters of regular and avalanche rectifiers. Real life conditions are simulated to maximize diagnostic capabilities. Additionally, analysis of the rectifier’s thermal resistance can be performed to detect poor internal diode connections and related defects.
-
product
Universal Test Machine Stands
FTUS
Portable, adjustable height, stands are available for all FTU chamber models. They support the chamber without transferring weight to your testing machine. Standard Universal Test Machine stands are furnished with an 18 inch, electrically actuated, lift system, four swivel casters with locks, and an all welded frame. Four types of stands are available
-
product
EMC Compliance Test Systems
ECTS2
Now in its second generation, the ADAPTIVE POWER EMC Compliance Test Systems use a greatly enhanced harmonics and flicker measurement system and newly designed flicker impedance options to support single and three phase AC harmonics, flicker and AC and DC immunity compliance testing up to the maximum required current of 75A per phase.
-
product
PSE Conformance Test Suites
Whether testing single port injectors or 48 port PSE’s, Sifos offers the ultimate solution to assess PSE conformance to all applicable IEEE specifications. With the click of a button, fully automated testing and reporting delivers comprehensive and informative results including difficult-to-spot intermittent conformance behaviors. Available to PSA-3000 and PSA-3402 PSE test instruments.
-
product
PSE Conformance Test Suites
2-Pair 802.3bt / 802.3at PSE's
*Robust 2-Pair 802.3at (Type-1, 2) / 802.3bt (Type-3) PSE Conformance Testing*Fully Automated Port Sequencing and Statistics*Greater than 95% 802.3at PICS Coverage from 23 Fully Automated Tests*Pop-Up Excel Reports Covering 1 to 24 Ports*Widely Used by PSE System and Silicon Manufacturers World Wide
-
product
Film Application & Test Charts
For numerous products, such as paint, ink, varnishes, glue and cosmetics, the reliability of many laboratory tests is directly related to the quality and consistency of the samples. Any measurements made on coatings for the purpose of describing their physical properties (drying time, elasticity, abrasion, gloss, colour, shade, etc.) are made on the basis of uniform and comparable samples with precisely controlled thickness.
-
product
E- And W-Band Test Assembly
StormFlex® 047EW
An SF047EW assembly offers test engineers, application designers, manufacturers of mmWave applications the proven durability and robustness of Storm Flex® 047 cable, optimized for coaxial connectivity at frequencies up to 110 GHz.SF047EW cable can withstand handling and flexing and while maintaining the original Insertion Loss and VSWR performance at frequencies previously addressed by waveguides.
-
product
Aviation Engine Test Cells
1.Design, manufacture and installation: ● Thrust stand components: thrust measurement system, adapter, superstructure etc. ● Facility subsystems: DAQ, supply systems (fuel, oil) etc.2.Civil construction works: site survey, building works etc.3.Contracting: ● Turn-key – MERA is able to supply a “turn-key” test cell including civil works, thrust stand, DAQ, all necessary facility subsystems, specialized software, throttle control level and etc. ● Joint – MERA is capable to supply specified items such as thrust stand with DAQ and software. The Customer is able to procure necessary items such as test nacelle directly from OEM. 4.Project management in accordance to EPC (Engineering, Procurement, Construction, FIDIC) 5.Certification in accordance to international and local standards and rules (SAE 5305) Engine types: PD-14, PS-90, RD-93, RD-33MK, AL-31FN
-
product
Heat Meter Test Bench
Bofa Instrument & Equipment Co., Ltd
1. Test bench accuracy with weight method (k=2)≤0.5%2. Test bench accuracy with standard meter method (k=2)≤0.7%Moreover:Flow testing accuracy (k=2)≤0.2%Temperature sensor accuracy (k=2)≤0.01℃3. Working pressure of water supply: 0.3~0.5MPa4. Range of flow:30~30000L/h5. Tested meter and diameter,DN15×6pcs, DN20×5pcs, DN25×4pcs, DN40×3pcs, DN50×3pcs6. Water tank max. working temperature 90℃, testing temperature 50±5℃, 85±5℃7. Thermostatic water tank (two channel)Temperature testing range : 4~95℃Temperature controlling range : 4℃~95℃; one channel : normal temperature +5℃~95℃ other channel working temperature difference≤0.02℃,8. Accuracy of electronic balance: 1/6000
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
HV DC Test Set
RX30/4P
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
Pil Dielectric Test Sets
DTS Series
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
product
Multi-Layer Network Test Platform
From fiber installation to service deployment, these platforms are designed to maximize network performance and accelerate the deployment of new services. Critical network parameters and performance can be monitored and network impairments quickly identified to accelerate the deployment of new services. A modular design with different size bay adapters allows you to customize your test set as needed adding further value.
-
product
Auto Electrical Test Bench
ELAK Auto Electrical Test Bench is a table model and has been designed to cater to the needs of Auto Electricians, Garages, Services Centers, Transport Corporations, Educational Institutions and other bulk users of Auto Electrical Equipments, for complete testing of Alternator, Regulator and their associated parts. It also has a built-in D.C. Power Supply to check Free-run of Starter Motors.
-
product
Tri-Axial Vibration Test Tool
AMHS and conveyor manufacturers utilize the Tri-Axial Vibration Test Tool to quantify and qualify the vibration characteristics during development, installation and maintenance of their systems. This industry-standard tool is used by 200mm and 300mm FABs to measure the vibration induced to wafer lots by their material handling systems. By detecting the early signs of track misalignment, systems can be maintained to minimize the vibration induced on the wafer lots.
-
product
Production Camera Test System
Meridian
Designed for rapid customization, the Meridian product line offers a revolutionary hardware and software approach to production camera testing. It's a flexible test tool kit that's compact, cost-effective and easy to incorporate in your production line: the graphical user interface facilitates setup and selection of metrology parameters; and a library of functions integrates easily into your testing software.
-
product
Residential Meter Test System
RADIAN RM-17
The Radian Research RM-17 Residential Meter Test System offers simplicity for testing residential watthour meters. In a compact, lightweight package of 7 pounds, the RM-17 delivers accuracy and flexibility in a practical solution to watthour meter testing. The RM-17 combines simple operation, advanced data management, and exceptional accuracy to provide a cost effective approach to field testing.
-
product
Wireless Router Test Platform
Promptlink Communications, Inc.
Promptlink's Wireless Router Test Platform (WRTP) is a complete functional router testing solution designed for the highest volume testing requirements. WRTP is the ultimate tool for accurate, high-demand testing of wireless routers. With added support for TR069 through Promptlink's own ACS, WRTP is the solution that gives you the ultimate power and productivity to keep your business moving forward.
-
product
Flying Prober Test System
QTOUCH1404C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
product
Test Finger Nail Probe
CX-75
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated test IEC60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the neccessary force for using the instrument. This probe is make of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
product
IEC60335 Nail Test Probe
CX-Z12
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated to test IEC 60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the necessary force for using the instrument. This probe is made of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
product
Embedded Configuration And Test Processor
SystemBIST
The SystemBISTTM Embedded Configuration and Test Processor - is a complete plug-and-play IP module built upon a unique patent-pending architecture. The SystemBIST processor is embedded onto a PCB, which enables design engineers to build high quality, self-testable and in-the-field re-configurable products. SystemBIST is vendor independent and can configure any IEEE 1532 or IEEE 1149.1 compliant FPGA and CPLD in-system.
-
product
ZY-3 Needle Flame Test
ZY-3/ZY-3S
According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.