Filter Results By:
Products
Applications
Manufacturers
-
product
Data Block Mating Table
VG Series
*Aircraft, Consumer Electronics, Networking, Telecommunications and Test Systems*Custom Blocks can be designed for your specific applications please contact your local sales person to find out more
-
product
8 Series Sampling Oscilloscope
The 8 Series Sampling Oscilloscope enables efficient and affordable optical component testing with an innovative disaggregated architecture. With a reconfigurable and compact design, an innovative user interface, and reliable high-end performance, this oscilloscope is an ideal test solution for manufacturing applications. The 8 Series is designed to adapt to a continuous increase in demand for higher bandwidths and baud rates addressing current and future test parameters.
-
product
Automated Bondtester
4600-W
The 4600-W Bondtester is a benchtop system designed to automatically perform complex test procedures without needing operator input. The system can automatically complete shear and pull test patterns with different orientations of bonds, while recording failure mode images upon completion.
-
product
Automated Bondtester
4600
The 4600 Bondtester is a benchtop system designed to automatically perform complex test procedures without needing operator input. The system can automatically complete shear and pull test patterns with different orientations of bonds, while recording failure mode images upon completion.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
Boundary-Scan Advanced Diagnostics Option for ScanExpress Runner
ScanExpress ADO
Being able to quickly pin point faults can provide the difference between a long night at the office or spending time at home with the family.ScanExpress ADO is designed to take diagnostic guesswork out of the equation. The fully automated analysis option quickly parses test vectors and identifies faults down to the net and pin level.
-
product
Boundary-Scan Test Executive
ScanExpress Runner
Efficiency in engineering means managing your most precious resources: time and effort. Automated testing is essential and boundary-scan is a critical component; no other structural test system provides the same value.When down to the wire, your boundary-scan test system needs to be built both for ease-of-use and reliability; a robust and powerful mechanism to ensure that no matter the state of production, all boundary-scan tests can be quickly and faithfully executed to maintain forward momentum.
-
product
Test Development Solution
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete "turn-key" service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
product
System-Level Interconnect Solution For ScanExpress Boundary-Scan Tools
ScanExpress Merge
Combine Multiple Assembly Test Files Corelis ScanExpress Merge, a member of the ScanExpress suite of boundaryscan test tools, is a software application designed to import and join test files for multiple independent assemblies and assist in configuration of a combined test procedure.Using completed ScanExpress TPG test files and module interconnection data, ScanExpress Merge quickly combines combined test plan files for system testing with minimal user effort.
-
product
Turnkey Boundary Scan Solutions
TestGenie
TestGenie is a low-cost boundary-scan solution for those companies that have a genuine requirement for JTAG testing, but have difficulty absorbing the tool costs or assigning the resources required to implement the test technology into their development or production processes. TestGenie allows customers to use full-featured versions of Corelis ScanExpress products at a fraction of the cost.Once you’ve selected boundary-scan as a practical solution, the second biggest decision is whether you want to do the test development yourself or have a third party do it. The decision should not be considered lightly as there are advantages and disadvantages to each.
-
product
Boundary-Scan Test Coverage Analysis Tool
ScanExpress DFT Analyzer
Test coverage statistics provide engineers and managers valuable information to make critical decisions in product development and manufacturing.ScanExpress DFT Analyzer is an automatic test coverage analysis tool for printed circuit boards and systems that include a mix of boundary-scan and non-boundary-scan devices. The tool assists design and test engineers to increase fault coverage and reduce boundary-scan test procedure development times. Using ScanExpress DFT Analyzer results in better informed test decisions.
-
product
Test Pattern Generator Software
ScanExpress TPG
To deliver a product meeting the highest standards of quality and reliability, design engineers and test engineers alike must maintain test capabilities throughout the entire product life cycle, from prototype to manufacturing. Automation in test generation is essential to ensure that tests keep up with the rapid development of modern products.The ScanExpress TPG™ Intelligent Test Pattern Generator Software provides a highly advanced, automated boundary-scan test design environment—perfect for quick and efficient creation of complete boundary-scan tests for all IEEE-1149.1 and IEEE-1149.6 compliant circuit boards.
-
product
Remote Intelligent Pod
ScanTAP
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Test & Programming Software
ScanExpress
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
product
Design For Testability Review
Design for Testability ReviewCorelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.
-
product
Test Program Execution for High-Volume Production Systems
ScanExpress Runner Gang
Electronic manufacturing test systems must be fast and efficient. Schedules today are shorter, products are more complex, and the market demands higher speed—the product needs to be built and shipped yesterday.ScanExpress Runner Gang Edition is a concurrent boundary-scan and in-system programming test executive designed specifically for high volume production. Unlike traditional test systems which execute sequentially on a single unit under test (UUT) at a time, ScanExpress Runner Gang Edition provides concurrent (gang) testing on up to 8 UUTs for improved test and programming times.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
JTAG Test Procedures
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete “turn-key” service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
product
Boundary-Scan Test / In-System Programming Controller
CPXI-1149.1/Turbo
The CPXI-1149.1/Turbo is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the CPXI-1149.1/Turbo offers up to 80 MHz clock rates on 4, 8, or 32 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
Monitoring Loops
The Loop Sensor was designed to monitor the generated magnetic fields in radiated susceptibility tests.
-
product
Monitoring & Drive Test Antennas
Linear polarized half-wave dipole with 1:1 balun and fixed element length for fieldstrength measurements at TETRA (terrestrical trunked radio) networks.
-
product
Test Systems
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
product
Electromagnet
The electromagnet can generate strong magnetic fields for experimental applications. Depending on the required magnetic flux density and Equipment under test volume the air gap can be adjustedcontinuously. The magnet poles come with conical shape close to the test volume to improve accessability and to optimize the achievable magnetic flux density.
-
product
Battery Simulator
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
product
MagTest System
A System to generate magnetic fields and to perform tests regarding the susceptibility against magnetic fields.
-
product
Pulse Generators
An electronic circuit or a piece of electronic test equipment used to generate rectangular pulses.
-
product
Electro-Stimulation Equipment Testing System
STIMU-600
Test device for functional testing of electrical stimulation devices.
-
product
Thermometer / Cardiac / Invasiv, non Invasiv Blood Pressure Simulator
TBH-400
Test device for functional testing of medical thermometers (DIN EN ISO 80601-2-56), cardiac output, invasive (IEC 60601-2-34) and non-invasive blood pressure devices (IEC 60601-2-30).