Showing results: 2701 - 2715 of 8631 items found.
-
AE -
Fuji Ceramics Corporation
Acoustic Emission (AE) is the sound emitted asan elastic wave by a solid when it is deformed or struck. The use of AE sensors to detect these elastic waves and to non-destructively test onmaterials is called the AE method.
-
American Environments Co., Inc.
A Test Specimens can be evaluated in two different modes in reference to acoustic noise: The Test Specimen's response to acoustic noise and the Test Specimen's generation of acoustic noise.
-
SPS-50 -
Kongter Test & Measurement Co., Limited
SPS-50 standard power source is applied for various tests of analog and digital AC voltage meter and current meter, single/three phase active and reactive power meter, phase angle meter, single/three phase power factor meter, frequency meter, and synchronous-meter, single/three phase active and reactive power meter. It also output 2nd ~63rd harmonics.
-
Chroma ATE Inc.
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
-
SPS-100 -
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
P Series -
Behlman Electronics Inc.
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
-
J2190A -
PICOTEST Corp.
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
80609010 -
6TL Engineering
The differential active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609000 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609007 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
ARA 01 -
York EMC Services Ltd
The Active Receive Antenna (ARA 01) is a compact emissions antenna with an antenna factor comparable to a conventional wideband passive antenna such as the Bilog. The small size makes the ARA 01 particularly suitable for use in anechoic chambers; however it can also be used on an Open Area Test Site (OATS) or at on-site locations.
-
Circuit Check, Inc.
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
AC-15 -
Tinker & Rasor
Monitors AC on pipelines or structuresAlarm at 15v AC ThresholdConforms to NACE SP0177-2007Audio and Visual AlarmsCalibration Test UnitSuperbright LED'sReplaceable 9v Batteries
-
8020 -
Chroma ATE Inc.
Chroma 8020 has standard test items specially customized and optimized for the features of Adapter and Charger that provides excellent test performance to meet the requirements of mass production. Meanwhile, the software equipped is very friendly and easy to operate that is suitable for production line use.