Filter Results By:
Products
Applications
Manufacturers
-
product
Portable Electricity Meter Testers
EE-120A-1S
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
product
Surface Insulation Resistance Testing
AutoSIR2™
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
product
High Voltage System
HV-2
International Electro-Magnetics, Inc.
*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.
-
product
Digital Insulation Mult-Meter
8010 IN
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 125V, 250V, 500V, 1000V● The maximum insulation measurement range is 200G ohm @1000V.● 1mA test current on insulation test at nominal voltage.● With a hand strap for easier holding.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III 600V IEC 61557-1 IEC 61557-2 EN 61326-1
-
product
Datacom Analyzers
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide E1/2M Transmission Analyzer is one multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks, mainly performing channel test, alarm analysis, fault finding and signal analysis. In addition, this instrument further provides various protocol converters with one-way and bi-directional bit error test function. These capabilities make it ideal for field use.
-
product
Cable & Insulation Testers
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
product
Vsync™ Controls Platform
Vsync™ is RedViking’s 4th generation powertrain dynamic testing software, based on over 100 fielded dynamic component test benches. Developed by RedViking for aerospace, automotive and off-highway test labs. Your lab or end-of-line test stand won’t have to rely on multiple stand-alone systems with limited data acquisition and analysis capabilities. Vsync™ provides an integrated, user-friendly platform for indisputable test data with superior repeatability and traceability.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
Autoranging Digital Megohmmeter - 1000V Digital Tester with Large Dual Backlit Display
380260
Extech Instruments Corporation
This autoranging megohmmeter measures insulation resistance up to 2000MΩ. Choice of 250, 500 or 1000VDC test voltages. The large backlit dual display indicates test voltage output and insulation resistance. Low resistance, continuity and AC/DC voltage measurement functions. Other features include automatic discharge at the end of test, protective holster with stand, power lock on feature and data hold. Complete with test leads, carrying case and 6 AA batteries.
-
product
Insulation & Multifunction Tester (LCD Display)
4167 MF
Standard Electric Works Co., Ltd
● High Quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Two insulation test voltages(DC) : 250V and 500V.● Alternation voltage measurement.● Battery life indicator.● Fuse protected.
-
product
3KV Digital Armature Surge Tester
D-3KAT
The Digital Armature Surge Tester with bar-to-bar test is a cost-effective solution to check the quality of Small to Large range of DC Traction Motors ideally suited for Railways. The Bar-To-Bar Test is provided to test the Low impedance of the Series wound Armatures and Field coils of DC Traction Motors. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
product
RF & Microwave Modules And Instruments
SHF Communication Technologies AG
In digital high speed test and measurement, a perfect clock signal is crucial for the generation of low jitter reference test signals. A SHF Synthesized Signal Generator (Synthesizer) used as a clock source can operate over several decades of frequency and is an essential part of any high speed test and measurement environment.
-
product
Bench Meters
LCR Meters
The measuring objects of LCR Meters are the parameters of impedance components, including resistance R, inductance L, quality factor Q, capacitance C and loss factor D. The selection of digital bridge should consider the highest frequency, test accuracy, test speed and DCR test function of the tested device.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
product
Digital Power Meter (High Accuracy Model)
LS2050
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
product
Evaluation Kit for Differential Pressure Sensors of the SDP3x Series
EK-P4
The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit consists of a USB stick connected to a PCB on which an SDP3x differential pressure sensor is already attached. The included flow element can be easily affixed to the kit with two screws and then directly connected to the gas flow. Detailed information about the flow element can be found in the application note.
-
product
150~300W DC Electronic Loads
JT631 Series
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Cells and Electrodes
Electrochemical cells are designed to their special purpose. The method, the matter and their reactions as well as the environmental conditions define the limitations and demands for electrochemical cells and the electrodes. Standard corrosion testing cells may have a large volume, since corrosion products shall not change the solution grossly during the test. On the other hand, it may be valuable to collect corrosion products - then a very small volume is desired ("eluation cell"). Special corrosion tests for pitting reqiure a setup where undesired crevice corrosion is excluded ("Avesta cell" , "Quarfort Cell" or "Flushed port cell". Or you want to investigate in crevice corrosion, then the cell design should meet such conditions. Have a look to the variety of cells shown here, and call us if you have a special task where a fresh design is required.
-
product
4500~6000W DC Electronic Loads
JT634 Series
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Peel Strength Testing
Peel Strength Testing is the average load per unit width of bond line required to separate bonded materials where the angle of separation is 180⁰. Peel testing is one way to characterize adhesive bonds. It is used extensively to evaluate the bonding strength of tape, adhesives and flexible substrates, including rubber, films, biomaterials, dental materials, medical packaging and consumables. Typical tests involve peeling two bonded flexible adhered from each other, or peeling a flexible bonded adhered from a rigid substrate. Peel tests are usually conducted at a constant rate at various angles, with 90° and 180° being the most common. Parameters such as peak peel load, average peel strength and statistical measures of peel strength variability are typically used to characterize behavior under peel loading.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Receiver, 9025, 25 Module, Slide Mount, Telescopic Handle - Right Side
310104477
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. This model is equipped with a telescopic handle on the right side. This handle is designed to rest flush against the side of the receiver as a standard handle, or can be extended out to the right up to 3" to accommodate a larger ITA enclosure or other obstruction that may prevent normal handle operation/ engagement.As with the standard 9025, a microswitch is included. Mounting flanges and an instrument bracket are also included for slide mounting. A slide kit is required, but not included. See 9025 procedure sheet/ user manual for instructions on choosing the correct slide kit length for your test rack. *Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
Receiver, 9025, 25 Module, Slide Mount, Telescopic Handle - Left Side
310104498
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. This model is equipped with a telescopic handle on the left side. This handle is designed to rest flush against the side of the receiver as a standard handle, or can be extended out to the left up to 3" to accommodate a larger ITA enclosure or other obstruction that may prevent normal handle operation/ engagement.As with the standard 9025, a microswitch is included. Mounting flanges and an instrument bracket are also included for slide mounting. A slide kit is required, but not included. See 9025 procedure sheet/ user manual for instructions on choosing the correct slide kit length for your test rack. *Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
Trainings, Seminars, Workshops
To make your staff able to face daily tasks and handle with high productivity is in the center of our trainings. Especially when a new test sytems starts to run it is extremely important that the personnel can operate appropriately from the beginning.Our workshops are designed as classroom trainings so everybody can concentrate completely on the workshop contents without being bothered by day-to-day business or other troubles.An alternative is the training in-house so we can look after individual and concrete problems directly on-site at the running test system.No matter if we teach in our rooms or in-house we emphasize to teach concrete practical content. The participants will spend at least 50% of their time with pracitcal questions or problems. Small groups ensure the individual care of each. We offer trainings in english or german language.
-
product
Low Loss Cable Assemblies
True Blue
The Answer: An unmatched combination of low loss, durability, and value.The Question: What does Teledyne Storm Microwave’s True Blue® line of cable assemblies provide?For more than 30 years, our True Blue® assemblies have been the winning choice of design, test, and production engineers for:- Military and aerospace design-in applications- General purpose test applications- Production testing- With a design based entirely on high-performance materials, the True Blue® line covers frequencies from DC to 50 GHz.Assemblies are available in both custom configurations and a variety of standard lengths and connector combinations.The basic True Blue® cable is designed to be durable. However, for applications requiring added durability, assemblies are also available ruggedized, armored, and soft armored.
-
product
Secondary Injection Equipment for Relay Testing
Portable equipment to test all types of protective relays and power system protection schemes. Automatic relay testing software, Comtrade transient playback and test reporting.
-
product
High Power & Voltage Pack Testing System
FTF
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
product
Battery Load Tester
BTM-15
Battery Load Tester Analog , Capacity of battery:100Ah, Rated test voltage:6/12 v, Voltage accuracy:+/- 0.2 v, Test cycle:10 seconds
-
product
Battery Load Tester
BTM-36
Battery Load Tester Analog , Capacity of battery:160Ah, Rated test voltage:12 v, Voltage accuracy:±3% F.S. Test cycle:10 seconds
-
product
Battery Load Tester
BTM-16
Battery Load Tester Analog , Capacity of battery:70Ah, Rated test voltage:6/12 v, Voltage accuracy:+/- 0.2 v, Test cycle:10 seconds
