Filter Results By:
Products
Applications
Manufacturers
-
product
PXI Resistor Module 4-Channel 1R to 255R with SPDT
40-293-113
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module 4-Channel 1R to 510R
40-293-014
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module 4-Channel 1R to 510R with SPDT
40-293-114
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Protocol Exerciser
Summit Z416
The Summit Z416 is a PCIe 4.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z416 can emulate PCI Express 4.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
MATCO TECH MULTIMETER
MD257
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
product
Bus Analyzer
Goebelyzer
Our Goebelyzer analyzer systems offer unparalleled insight into bus data and are used in flight test, system simulation, LRU design, verification and manufacturing test. Supported Interfaces Arinc 664, ASCB-D, Honeywell Flight Controls P2P, Arinc 429, CAN2.0b, Mil Std 1553, RS 422 SDLC/Async, ADC
-
product
Temperature, Humidity And Others Relevant Environment Tester
King Design Industrial Co., Ltd.
Allows your product quality and reliability tests more realistic toward actual environment; simulate the actual environment in the temperature, humidity and vibration by separated of combined tests. The tester is equipped with control panel, Chinese-English display and micro-computer temperature control system; applicable to aerospace, military, vehicles, electronics and other high-tech products.
-
product
Software for System-Based Protection Testing
RelaySimTest
RelaySimTest is a software solution for system-based protection testing with OMICRON test equipment that takes a novel, future-oriented approach: the test is independent of relay type and relay manufacturer and the often very extensive parameter settings. Instead, it completely focuses on the correct behavior of the protection system. This is made possible by simulating realistic events in the power system.
-
product
Thumpers and Cable Fault Location
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
product
Impulse Generators and Measurement Systems
Designed to generate impulse voltages that simulate lightning strokes andswitching surges as defined by IEC, ANSI/IEEE, and other national standards on:• Distribution transformers• Small power transformers• Cables (type tests)• Arrestors (impulse current tests)• Motors / generatorsTesting ApplicationsImpulse Generators andMeasurement Systems• Insulators• Bushings• GIS• Instrument transformers
-
product
Transformer ON-Load Tap-Changer Tester
WAYZ-2011
Wuhan Sangao Electrical Test Installations Limit Co.
This Transformer on-Load Tap-Changer Tester is acc to Chinese Electric Power Industry Standard, It also can meet the requirement of electrical equipment handover and prevention test standard.To achieve the accurate measurement of on load tap changer's transition time, transition resistance,three-phase synchro nization parameterssyn.It is the best test equipment of on-Load Tap-Changer.
-
product
Bit Error Ratio Testers
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
product
3 Wire (Analogue) Earth Resistance Tester
ST-1505
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● The timer operates automatically for about three to five minutes when the “PUSH BUTTON SWITCH” and “TIMER ON BUTTON” are pressed together. ● This will keep test “ON” for the duration of the timer.● Battery check function.● Calibration performed with supplied test leads.
-
product
End to End Testing
TestOrigen Software Testing Services Pvt Ltd.
End to End Testing basically refers to the method that verifies the application is performing according to users demand. While executing the E2E test, the complete software system from beginning to end is certified. This is done after functional and system testing and is also carried out as a regression test to validate and verify any patches or changes.
-
product
ATE Core Configurations
ATE Core Configurations streamline the design, procurement, and deployment of automated test systems with highly integrated mechanical, power, and safety system infrastructure. These off-the-shelf systems reduce lead times and simplify standardization and global deployment. Lower your total cost of ownership for your test systems with ATE Core Configurations.
-
product
PXI Source/Measure Unit
Keysight PXI source/measure unit (SMU) offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. It delivers industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading for faster test time.
-
product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
Winding Resistance Meters
The NMC 'TDR' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. 'TDR' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. 'TDR' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.
-
product
Flushing Stand for Power Steering System
MS603N
Test Bench for flushing of power steering system under pressure and diagnostics of power steering system units. The equipment measures power steering pump pressure under different speed; detects failures as leak, roar, body wear out, reducing valve sticking. The test bench measures power steering rack flow and pressure; detects failures as leak; wear out of seals, body and teflon rings. The equipment tests operation of units under different loads (in motion, parked). Top features of the equipment are small sizes, mobility, battery operation.
-
product
Hipot Wire Harness Testers
NX Hipot
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
product
PXI 2A 39xSPST High Density Power Relay Module
40-137-201
These Power Relay Modules are suitable for applications requiring power relay switching with high density. The feature 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 39 x SPST version, the range also includes a 32 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
Regenerative AC Load
61800
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
product
Three Phase Reference Standard Meter
Signals & Systems India Private Limited
The Three Phase Reference Standard Meter (TPRS-1107) is portable equipment from SANDS. The main objective of this device is to calibrate the errors in three-phase and single-phase energy meters i.e. the meter under test (MUT). The TPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, power factor etc of the meter under test. It has an LCD display, an alphanumeric keypad that makes it easy for the user to operate the TPRS. It can be interfaced with the PC for data analysis. It has the capability of storing up to 8000 test results.
-
product
PXI 2A 32xSPST High Density Power Relay Module
40-137-101
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
product
High Voltage EMC Surge Generator
TM510
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
product
Vibration Testing Equipment
Wewon Environmental Chambers Co, Ltd.
In Wewon, We have 2 powerful Vibration Testing Equipment. The Vibration Testing Equipment A is : EV210H0808VCSusb-E; The Vibration Testing Equipment B is: EV232H0809VCSusb-E. Technical parameters as below blank forms mentioned, The mainly difference is Sine Excitation Force, Frequency Range, Vibration Table’s size. Application for Vibration Test Equipment : The vibration test is to inspire or impact a part or device to see how it reacts in a real environment. The application of vibration test is very extensive, from the circuit board, aircraft, ships, rockets, missiles, automobiles and household appliances and other industrial products.
-
product
Semiconductor Package Wind Tunnel
WT-100
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
product
Digital Surge Tester
KT-905D
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.