Showing results: 226 - 240 of 280 items found.
-
510151108 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510150131 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510150135 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
510151127 -
Virginia Panel Corporation
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
IFDIS -
Copernicus Technology Ltd
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Smiths Interconnect
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Smiths Interconnect
Diamond is the best thermal conductor on earth. Combined with a low dielectric constant, it is an excellent RF dielectric material for high-frequency applications in which thermal performance is equally critical. By applying cutting-edge thin film process and extensive millimeter wave design experience, Smiths Interconnect has created a high-performance line of resistive components. The resulting products, our Diamond RF Resistives® resistors, terminations, and attenuators, are significantly reduced in size and unparalleled in average and peak power handling.
-
STAR-Dundee
The STAR Fire Mk3 is a test and development unit that can emulate, stimulate, debug and validate SpaceFibre enabled equipment. The STAR Fire Mk3 can transmit and receive both SpaceWire and SpaceFibre traffic; it can interconnect SpaceWire equipment to a SpaceFibre network; and it can operate as a SpaceFibre link analyser, capable of unobtrusively capturing and displaying SpaceFibre traffic. MICTOR connectors on the rear of the unit allow decoded SpaceFibre signals to be viewed on an external logic analyser. Integration with external equipment is possible using SMB connectors.
-
34939A -
Keysight Technologies
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
787325-01 -
NI
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
CA9806-12 -
UC Instruments, Corp.
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
SmartPhone D -
Teledyne Marine Real Time Systems
The highly rugged encapsulated SmartPhone D was designed for use with the SmartSource controller, or SmartPhone D system, for real-time monitoring of near-field signatures. The integrated 24-bit digitizer at the sensor element provides the lowest noise interconnect between the phone element and digitizing electronics, eliminating the issues of long signal lines and cross coupling while providing unprecedented signature fidelity at a sample rate of 2 kHz. The unique straight-to-digital design allows more flexibilty in umbilical design by providing digital communications clarity with even the longest of umbilicals. Built-in calibration ensures that the system will always report calibration levels. An on-board disciplined precision oscillator provides PPM-level sample rate accuracy. Built-in testing features and self-monitoring provide the user with instant assessments of the health of the phone.
-
Acromag, Inc.
VPX boards (VITA 46) are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O with serial fabric interconnect technologies. Carrier cards with PCI Express provide a simple and cost-effective solution for interfacing a PMC or XMC I/O modules to a VPX computer system. VPX FPGA modules offer great flexibility and performance for custom computing applications. Depending on your system’s operating environment, you can select air-cooled, conduction-cooled or Ruggedized Enhanced Design Implementation (REDI VITA 48) versions.
-
Bloomy Controls, Inc.
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
E5071C -
Keysight Technologies
9 kHz to 4.5/6.5/8.5/14/20 GHz2- or 4-port, 50 ohm, S-parameter test set Improve accuracy, yield and margins with wide dynamic range 130 dB, fast measurement speed 8 ms and excellent temperature stability 0.005 dB/CObtain design confidence through complete characterization of high-speed serial interconnects with enhanced time domain analysis option Protect your investment with upgradability across all of the options Every spec verified, adjustments included Lock in support & peak performance from the start
