Showing results: 661 - 675 of 1039 items found.
-
Virginia Panel Corporation
The 9025 VXI Receiver is a 25-module solution designed for use with VPC pre-wired interconnect adapters, but can also accommodate a combination of pre-wired interconnect adapters and discrete-wired modules using retainer blocks.1-4 modules attach to an interconnect adapter which in turn is attached to the VXI card. This connector “funnel” forms a complete VXI module, which is easily inserted or removed from the VXI mainframe for maximum flexibility in testing applications. The interconnect adapter also provides room for driver sensors. External cabling to the card is done with a cable clamp or connector located on the top or bottom of the adapter. The positioning of funnels and use of discrete wiring modules can affect the performance of the product. Please contact us for technical assistance.
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator. More then 500 Indian pump manufacturer ware installed this system & satisfied with performance.
-
Santa Barbara Infrared, Inc.
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
IP750 -
Teradyne, Inc.
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
CA9806 -
UC Instruments, Corp.
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
ICPE-9800 Series -
Shimadzu Corp.
Due to their high detection sensitivity down to ppb levels, ability to analyze a broad 5 to 6-digit range of concentrations, and ability to measure multiple elements simultaneously, ICP emission spectrometers are used in a broad range of fields, such as environmental testing, pharmaceuticals, foods, chemicals, and metals. ICPE-9800 Series of simultaneous ICP atomic emission spectrometers are next-generation systems that offer the superior accuracy necessary to simultaneously and quickly analyze multiple elements regardless of their concentration levels. They also feature user-friendly software that makes analysis easy. Furthermore, the systems reduce analysis costs while providing the highest performance levels in the industry. ICPE-9800 Series systems represent the ultimate in ICP atomic emission spectrometry for environmental, pharmaceutical, food, chemical, metal, and other fields.
-
GRL-UHSII-EMU -
Granite River Labs Inc.
Developed in cooperation with Tokyo Electron Device (TED), GRL’s UHS-II Protocol Card Tester & Host Emulator (GRL-UHSII-EMU) is the only tool that tests conformance with SD Association UHS-II Protocol Test Guideline Version 1.0 at the click of a button. This combined Hardware and Software test platform provides a self-verification environment for UHS-II Card and Host, covering almost all items defined in the SDA UHS-II Protocol Test Specification as well as a highly configurable environment for stress testing and validation. GRL-UHSII-EMU validates the reliability of UHS-II Cards/Hosts by allowing tests to be run in random or sequential order, or continuously to identify card performance over a period of time. The tool provides easy-to-understand Pass/Fail test results and protocol trace captures.
-
PXIe-9852 -
ADLINK Technology Inc.
The ADLINK PXIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PXIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference, the PXIe-9852 provides both high accuracy and high dynamic performance, making it ideal for applications requiring high-speed data acquisition, such as optical fiber and LIDAR testing, and video signal analysis.
-
PCIe-9852 -
ADLINK Technology Inc.
The ADLINK PCIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PCIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference, the PCIe-9852 provides both high accuracy and high dynamic performance, making it ideal for applications requiring high-speed data acquisition, such as optical fiber and LIDAR testing, and video signal analysis.
-
Lisun Electronics Inc.
Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.
-
Delaire USA, Inc.
The Delaire USA LTE RF Communication Subsystem is designed to provide a versatile solution for the testing needs of the next generation wireless systems. With the LTE test subsystem developers can build an end-to-end test environment for complete system operation. From end user equipment and eNodeB base stations to full system functionality, the LTE RF Communication subsystem allows developers to test and evaluate equipment and system performance in a controlled laboratory environment.
-
BVM-1010 -
BYC Industrial Ltd
M-LCD Video Microscope has renovated the traditional way of microscopic observation and adopted a modern way of electronic imaging. This patented microscope makes the observation more comfortable and thoroughly resolves the fatigue caused by using a traditional microscope at work for a long time. It features high performance of CCD image capturing, high resolution of LCD display and reverting genuine images. Based on 2D observation, 3D angle attachment is added to obtain 3D multi-angle observation. Laser locating function can easily identify the position of observation. This unit integrates magnification, imaging, display, LED illumination and laser locating functions. Compact design, light weight and low power consumption make the operation simple and convenient. M-LCD Video Microscope can be conveniently applied to testing and inspecting in product assembly, research and teaching fields.
-
MPA-100 -
Santec Corporation
MPA-100 is a highly integrated rack mountable model of pigtailed photo-detectors. Multi-channel optical power from MPO or MTP connectors are measured. Photo-detectors of Silicon type for 850 nm range and InGaAs type for 1260 - 1610 nm are available. The detected photo-current is converted into a voltage output using a 16-bit multi-channel DAQ interface. The dimensions are (W) 482.6 x (D) 430 x (H) 44 mm. The highly integrated MPA-100 is available up to 80 channels with an excellent cost performance and small footprint. The MPA-100 is useful for many 40 GbE / 100 GbE applications, such as testing and monitoring of transceivers (SR4, SR10, LR4, and ER4) for data communications, broadband / CATV, and telecommunications. Tap-PD model (Eg. a partial 5 % tapped power detection) is also available with customization.
-
SDL1000X/X-E Series -
SIGLENT Technologies
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
