Showing results: 346 - 360 of 1346 items found.
-
Laurel Electronics, Inc
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
Advantech Co. Ltd.
Advantech USB serial device server allows PC users to connect serial devices via a LAN to systems. They allow access from anywhere on your network.
-
7803ec -
Sealevel Systems, Inc.
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
FT232H -
Adafruit
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
RS485-MOD2 -
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
Xeltek
In-circuit serial programming, also known as in-system programming (ISP) or in-circuit programming (ICP) enables programming and reprogramming of microcontrollers, serial EEPROMs and flash memories already soldered on a target PCB.
-
cPCI Serial 3U -
Kontron
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
7202ec -
Sealevel Systems, Inc.
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
J7000 -
Noisecom
The J7000A Series instruments high crest factor output is used as a random jitter source for serial data bus applications, including PCI Express Gen I & II, Serial ATA, and Fiber Channel. The noise source is designed for the PCI-SIG total jitter (Tj) model serial data application, but can be used for any random jitter noise application.
-
7804ec -
Sealevel Systems, Inc.
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
W-IE-NE-R, Plein & Baus GmbH
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
-
PCIe-Mini-ESCC -
ALPHI Technology Corporation
The PCIe-Mini-ESCC module is a Dual Channel serial communication controller with 4K FIFO per Line. The PCIe-MiniESCC module is based on the Z85230 Enhanced Serial Communication Controller, with larger FIFOs and several SDLC improvements from Zilog.
-
East Coast DataCom, Inc.
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
T3DSO2354A -
Teledyne LeCroy
Optional Serial Bus Trigger and Decode options – I2C, SPI, UART, RS232, CAN, LIN which enables users to debug serial buses directly to their Oscilloscope on the T3DSO2000 series. While on the T3DSO2000A series I2C, SPI, UART, CAN, LIN Serial Bus Trigger and Decode options come as standard with optional CAN FD, FlexRay, I2S and MIL-STD-1553B also available on the T3DSO2000A series.
-
T3DSO2502A -
Teledyne LeCroy
Optional Serial Bus Trigger and Decode options – I2C, SPI, UART, RS232, CAN, LIN which enables users to debug serial buses directly to their Oscilloscope on the T3DSO2000 series. While on the T3DSO2000A series I2C, SPI, UART, CAN, LIN Serial Bus Trigger and Decode options come as standard with optional CAN FD, FlexRay, I2S and MIL-STD-1553B also available on the T3DSO2000A series.