Showing results: 181 - 195 of 1818 items found.
-
DSP-1L -
Controlab Inc.
Is used to protect your three-phase motors against loss, imbalance or inversion. It continuously monitors each phase of your power supply. In case of phase loss, imbalance or inversion, the DSP-1L cuts off the power to the control circuit and thus protects the motor concerned.
-
WDFZ-5T/10T/15T/20T -
Langeo Co., Ltd.
The new DC IP transmitter system is composed of WDZ-5A (WDZ-10) rectification power supply (including balanced load controller) and WDFZ-5T (WDFZ-10T) multi-channel high-power intelligent transmitter.
-
Optomistic Products
The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
post2b -
PC Engines Gmbh
Post2b = ISA POST code display, not RoHS compliant (can be considered test equipment, not subject to RoHS). Spec? During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h. Use post2b to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size?
-
Renesas Electronics Corp.
The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.
-
H62005200 -
6TL Engineering
2×4 Terminal points for 24Vdc2×3 Terminal points for 15Vdc
-
Analog Devices Inc.
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
Blackhawk
Need a replacement part, cable assembly, power supply? Blackhawk stocks the part and accessories you need for development with our line of JTAG Emulators.
-
LEC-Starterkit 2.0 -
ADLINK Technology Inc.
The LEC-Starterkit 2.0 consists of a SMARC 2.0 compliant LEC-BASE 2.0 carrier board, data media, an AC/DC adapter, power cords and is suitable for LEC-AL, LEC-BT, LEC-BTS or LEC-BW modules.
-
-
LS 150 Xenon Arc Lamp Source -
ABET Technologies Inc.
Model LS-150 is a Patented US Pat. No. 8116017 low cost, high output 150 watt Xe arc lamp based light source. The entire source, power supply, lamp, and optical compartment are housed in an extremely compact enclosure, 9 x 6 x 11 inches. The unit's base allows mounting on inch or metric spaced optical tables with the optics centered over the hole pattern to allow for easy integration with the rest of your setup.
-
SparkFun Electronics
The LilyPad Simple Power is a simple e-textile board with a 500mA charge rate that lets you connect and charge a lipo battery and switch it on or off, that's it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in added a bit of power to your next wearable circuit.
-
Series MPS -
Kepco, Inc.
Series MPSThe MPS is a 70 Watt, triple output MIL-STD-461 compliant power supply specifically designed to meet the needs of IC/microprocessor experimenters. It is actually two linear (series pass) power supplies in one.The first has a single 0-6V, 0-5A output backed up by an adjustable current limiter and overvoltage crowbar for digital work. The second has two tracked outputs, 0 to +20V and 0 to -20V, both rated at 0-1 Amp. The two power supplies are completely isolated from each other, sharing only the front panel meters and the chassis.
-