Showing results: 1606 - 1620 of 4066 items found.
-
Model 901 -
Rinch Industrial Co.,Limited
Intelligent chip design. Ability to set and store the stirring rate. Ability to switch between two kinds of stirring speed after pressing “PRM” button.Options of AC and DC. Applied in the field or in the incubator. MoreIntelligent chip design. Ability to set and store the stirring rate. Ability to switch between two kinds of stirring speed after pressing “PRM” button.Range: 0 to 2300 R/M (no load)Nice appearance, transparent coping designused with AC or DC, and a battery low voltage alarmused in lab, in incubator and brought outdoorsEquipped with strut and electrode holder, it can be used as agitating arc-spark standIP54 dustproof and splash proof.
-
Model 300 -
Rinch Industrial Co.,Limited
this thermometer is a digital hermometer fr use with any K-type thermocouple as temperature sensor. temperature indication follows IEC584 temperature/voltage tables for K-type thermocouples.
-
MODEL SS1 -
Paralan Corp.
The SS1 SCSI Bus Switch allows two hosts to share peripherals or one host to access either of two sets of peripherals. Each port may be SE, HVD or LVD. Switching from one port to the other may be accomplished: a. locally with the front panel switch, b. remotely with a momentary dry contact closure, or c. remotely via the RS-232 port. A software template for the RS-232 port is included in the User Manual. In all cases switching does not occur until "bus free."
-
Model 2019A -
Aplab Limited
- Versatile Waveform Generation for a Wide Range of Testing Application- Wide Range of Frequencies from 0.0002Hz (i.e. 5000s) to 20MHz (i.e. 50ns)- Choice of Eight Selectable Waveforms- All Outputs can Drive 50 ohms Terminations- Trigger and Gate Modes with Adjustable Start/Stop Control
-
Model 4060 -
Teledyne Analytical Instruments
The 4060 Series speciates gases of interest by combining well-accepted gas chromatography techniques with field-proven detector technologies. This combination, along with effective electrometer-based signal amplification and temperature controls, enables the series to detect either single or multiple compounds in a background gas possessing potentially interfering compounds.
-
Model 8800A -
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
Model 7600ZA -
Teledyne Analytical Instruments
The 7500Z and 7600Z Series Infrared (IR) Analyzers are capable of detecting up to four chosen, individual IR absorbing components (i.e. CO, CO2, CH4, SO2, NO or NOX with external converter) on a continuous basis. Conveniently packaged in a 19” rack mount, the analyzer can also be supplied with an oxygen sensor, providing the operator with space saving, five in one, cost-effective design. The NEMA-4 enclosure can be purged to meet Class I, Div 1 (Zone 1) or Class I, Div 2 (Zone 2) hazardous area installation requirements.
-
Model 8800P -
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
Model 8800B -
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
Model 3000MB -
Teledyne Analytical Instruments
The 3000MB analyzers are versatile, microprocessor based instruments specifically designed to detect oxygen in a variety of gases. They are precise, cost effective instruments capable of measuring percent oxygen in as low as the 0-1% range. Drawing on the solid performance of the highly successful 3000 Series control platform, these provide the user with a wide variety of features and options to satisfy virtually any application.
-
Model 3190 -
Teledyne Analytical Instruments
The 3190 analyzer proves that good things come in small packages. This microprocessor based unit offers high accuracy, easy use and all the standard features demanded by the end-user in a compact, budget priced design. Membrane command switches and a large, four digit LED display make setup and operation clear and quick.
-
Model 3290 -
Teledyne Analytical Instruments
The 3290 analyzer proves that good things come in small packages. This microprocessor based unit offers high accuracy, easy use and all the standard features demanded by the end-user in a compact, budget priced design. Membrane command switches and a large, four digit LED display make setup and operation clear and quick.
-
Model 3300TB -
Teledyne Analytical Instruments
The 3300 series of low cost, microprocessor-based instrument are specially designed to satisfy industry’s need for a simple yet highly reliable process analyzer. These units offer excellent accuracy, ease of use, high reliability, low maintenance and a variety of standard features usually found on more expensive instruments.
-
Model 6400TH -
Teledyne Analytical Instruments
The 6400T Series analyzers uses a proven UV fluorescence principle coupled with state-of-the-art microprocessor technology to provide accurate and dependable measurements of low level SO2. The 6400T-H2S measures hydrogen sulfide (H2S) by incorporating a catalytic converter set at 600°F (315°C) to oxidize H2S into SO2 while leaving other more difficult to oxidize sulfurs unconverted. A switching mode allows analysis of both H2S and SO2 concurrently.
-
Model 2000B -
Teledyne Analytical Instruments
The Series 2000 represents a complete line of Thermal Conductivity Detector (TCD) based analyzers which can be applied in a wide range of applications and industries. By using field proven filament-based and semiconductor based TC detectors, Teledyne is able to continuously monitor hydrogen and a variety of other gases of interest in either binary or multi-component sample gas streams.
