Showing results: 376 - 390 of 1161 items found.
-
-
-
KP Technology
Our large range of Scanning Kelvin Probes gives the user full access to 2D and 3D work function plots of samples ranging in size from 50 mm to 350 mm. With work function resolution of 1 - 3 meV, and the spatial resolution of the Probe tip diameter (0.05 mm with the SKP5050 model), the Scanning Kelvin Probe gives reliable, repeatable measurements for work function, contact potential difference and Volta potential.
-
Equip-Test Kft.
Fine pitch, 0.20 mm [8 Mil] - single & double ended - non-rotating - kelvin - RF - high performance.
-
3D Fiber Probe -
Werth Inc.
Ultra high precision 3D measurements2D image processing combined with a laser distance sensorSelf illumination modeLowest contact force of 1 µNProbe sphere diameters from 0.040 mm to 0.250 mmControl and evaluation software for fully automatic measurements
-
30C9 -
Delcom Instruments Inc.
For thick conductive materials or conductive coatings on a thick substrate. The 30C9 sensor has a 30 cm reach and 9 mm gap.
-
SolGel Technologies GmbH
active areas from 0.06 mm² to 36 mm² and quadrant photodiodes for position determinationUV broadband sensitivity or with optional filters for UVA, UVB, UVC or UV indexdifferent entrance windows and housing designsown SiC chip production since 2009PTB-published high radiation hardnessPhotodiodes catalog
-
OSC-700 -
OPTOKON a.s.
The OPTOKON OSC-700 is an automatic fusion splicer for SM, MM, DS, NZ-DS (G655), EDF and other fibers. The OSC-700 is capable of ensuring high-quality splicing even in the most unfavorable environment conditions. The OSC-700 splicers are suitable for core or cladding alignment. Using one of these methods the two cleaved fibers are automatically aligned by the fusion splicer in the X, Y plane, then are fused together. The bare fiber area is protected either by recoating or with a splice protector. A splice protector is a heat shrinkable tube with a strength member and less loss.
-
EST-5 -
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
EST-6 -
Technopark Automation & Control
The EST-6 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 500 mm. This load cell is available in capacities 500 kg and 1000 kg.
-
EST-4 -
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
SCM120 -
Axiomtek Co., Ltd.
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
TBCP2-250 -
TekBox Singapore Pte. Ltd.
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
TP32MTT.03.B -
Delta OHM S.r.L.
Temperature probe with two 4-wire Pt100 1/3 DIN sensors for measuring the soil and air temperature (± 50 mm).
-
TP32MTT.03.A -
Delta OHM S.r.L.
Probe for soil temperature at a depth of 50 mm - protective shield from solar radiations.