Showing results: 301 - 315 of 4056 items found.
-
PTE-FCN -
EUROSMC, S.A.
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
TRES -
EUROSMC, S.A.
With high power outputs packaged in an extremely compact and rugged system, the TRES has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
6R Series -
Mors Smitt Group
The 6R MATRIX range was developed to provide design engineers with a modular system of auxiliary relays to meet specific system configurations. The versions described in the following cross reference table have pre-defined functional & contact configurations to offer the following advantages:*Simple to specify & order*Lower cost due to model rationalization*Direct cross reference to other manufacturers models*Standardized wiring details
-
SFJ018 -
Shanghai Launch Electric Co., Ltd.
SFJ018 relay protection test cabinet uses double carbon brushes regulator, big buttons for regulating AC/DC voltage, current under large loading, small buttons for regulating AC/DC voltage, current under small loading,. The two output channels could work simultaneously. It also take use of digital meters of Grade 0.5, sensor of high accuracy, six digital display stop watch, satisfying requirements for time measurement.
-
Part No. E3P2G -
Teledyne Defense Electronics Relays & Coax Switch
The E3P2G series, three-phase solid state relay is the 2nd generation of the discontinued E3P series. The new design incorporates a high efficiency back-to-back thyristor with direct copper bonding for a longer lifetime expectancy. Over-Voltage protection is provided internally with TVS diodes for the input and output. Additionally our -16 model is designed with an RC snubber and VDR for greater protection to the output to handle all types of loads. The industrial SSR utilizes optical isolation to protect the control from load transients for each phase and has tight zero-cross window for low EMI. A control status LED are standard on all models.Available options include:E3P48D25 Load: 25A, 24-600Vrms ; Control: 4-30Vdc E3P48D50 Load: 50A, 24-600Vrms ; Control: 4-30Vdc E3P48D75 Load: 75A, 24-600Vrms ; Control: 4-30Vdc E3P48D75-16 Load: 75A, 24-520Vrms ; Control: 4-30Vdc ;E3P48D75-16 RC+VDR Output Protection
-
B-1007 -
ROSS ENGINEERING CORPORATION
Extra high voltage, low corona, grounding relays of the air insulated type. Peak test ratings up to 300kV and 100 amps continuous. Units can be operated either by solenoid, motor, or air cylinder, with spring or gravity return. All models have spherical contacts. When voltage transient limiting is required, some models have an adjustable sphere gap. Also available are units with built-in high voltage discharge resistors with energy dissipation capabilities from 50 to 10,000 ohms. Some units can be reduced in height if full line to ground voltage is connected to the top high voltage contact only and the other high voltage terminal is operating at, or near, ground potential. Line to ground voltage can also be increased by adding insulation between lower high voltage contact and ground. Normally mounted base down. Base up mounting if specified.
-
SEL-387 -
Schweitzer Engineering Laboratories, Inc.
Protect and control any two-, three-, or four-winding power transformer with the SEL-387, which provides thermal and through-fault monitoring, and with SELogic Control Equations, can detect breaker failure.
-
SEM1630 -
Labfacility Ltd.
The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual trip output
-
mPCIe-IIRO-8 -
Acces I/O Products, Inc.
The mPCIe-IIRO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Series 111 -
Pickering Electronics
Requires a board area of only 0.15 x 0.4 inches (3.8mm x 10.2mm). Pins on 0.1 inch pitch as 110 & 112. 3 Watts switch in Mu-metal or Plastic package (not illustrated).
-
Series 115 -
Pickering Electronics
SoftCenter construction Highest quality instrumentation grade switches Plastic package with internal mu-metal magnetic screen They take up the minimum of board area, conservingboard space Insulation resistance greater than 1E12 Ohms 100% tested for dynamic contact resistance for guaranteed performance 5 or 12 Volt coils with optional internal diode
-
SEL-2664S -
Schweitzer Engineering Laboratories, Inc.
Protect high-impedance grounded generators from ground faults at standstill, during startup, and while running with the multisine frequency injection and neutral overvoltage-based protection in the SEL-2664S.
-
AK-30 -
Amperis sl
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
AK-6 -
Amperis sl
*5 automatic or manual test modules: DC test, AC test, distance test, harmonics and frequency protection*Phase, frequency and amplitude are continuously and independently adjustable.*All-in-one design: built-in Windows CE & rotary encoder & keyboard & 6.4" TFT LCD (RJ45/USB for updates and downloads)*High power: 3x450VA at 0...35A average voltage test
-
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations. It is further necessary that these expanding testing capabilities be met with a similar improvement in the simplification of a test instrument’s user interface and software control.