Showing results: 886 - 900 of 1119 items found.
-
72-7226 CAL D -
Tenma
The 72-7226 CAL D from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
Talon RTR 2736A -
Pentek, Inc.
- Designed to operate under conditions of shock and vibration- Portable system measures 16.0" W x 6.9" D x 13.0" H- Lightweight, just less than 30 pounds- Shock-and vibration-resistant SSDs perform well in vehicles, ships and aircraft- Up to eight I/O channels- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125, and 4.25 GBaud link rates- Copper, single-mode and multi-mode fiber interfaces available- Real-time aggregate recording rates up to 3.2 GB/sec- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor- Up to 61 terabytes of SSD storage to NTFS RAID solid state disk array- SystemFlow® GUI with Signal Viewer analysis tool- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
61700 series -
Chroma ATE Inc.
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
MEXA-ONE-FT -
HORIBA, Ltd.
The MEXA-ONE-FT Series simultaneously measures concentrations of multiple components, including NH3, N2O, CH4, CO and CO2, in undiluted exhaust gas using the Fourier transform infrared (FTIR) method in combination with a multivariate analysis algorithm. It incorporates HORIBA's proprietary compact interferometer which yields superior performance and high accuracy.The system complies with NH3 testing requirements of Euro VI, the EU regulation for heavy duty emissions testing.The MEXA-ONE-FT can be calibrated according to customer requirements with up to 6 component sets to cover a wide range of applications.FTIR spectroscopy allows the direct measurement of NO2 emissions and the independent quantification of individual hydrocarbon species. This makes the MEXA-ONE-FT system an ideal solution for detailed research and development tasks.Due to the measurement principle, the time-consuming daily span gas calibration is omitted.In addition, usability and flexibility are realized by “HORIBA ONE PLATFORM” which enables to extend the system with other ONE analyzers to a complete solution suitable for both certification and R&D purposes.
-
RedLux Ltd
Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.
-
MACC II - Converter -
Excalibur Systems, Inc.
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
TURNS-LCRTZ -
Vasavi Electronics
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
-
Talon RTR 2729A -
Pentek, Inc.
- Video: A Quick Look at RTR 2729A Talon Rugged Portable Recorder- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9"D x 13.0" H- Lightweight, just less than 30 pounds- Sample rates up to 3.6 GHz in single-channel mode- Sample rates up to 1.8 GHz in dual-channel mode- 12-bit A/D, with 16- and 8-bit packing modes- Capable of recording RF/IF frequencies to 1.75 GHz in single-channel mode- Capable of recording RF/IF frequencies to 2.8 GHz in dual-channel mode- Real-time sustained recording rates of up to 4.0 GB/sec- Windows® 7 Professional workstation with high-performance Intel® Core™ i7 processor- Up to 61.4 terabytes of SSD storage to NTFS RAID solid state disk array- SystemFlow® GUI with Signal Viewer analysis tool- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
MS002 COM -
MSG Equipment
A high power multifunctional test bench includes the following diagnostic functions: diagnostics of starters, alternators and voltage regulators without applying any additional measuring devices. The test bench was invented on the basis of the requirements of modern service stations: construction implies mounting of majority of units without using additional fixing elements. The bench tests units of 12V and 24V; diagnoses the latest alternators and voltage regulators, which are controlled by car ECU; has ports to connect alternators of different brands and manufacturers: COM (LIN, BSS), P-D, DFM, D+, RLO, C, SIG. Diagnostics is carried out through load simulation of car consumers, change of rotation speed, sending of control signals (external control alternators), tracking of electrical characteristic. Testing results are transmitted to LCD display real-time. Testing modes are switched with membrane keyboard on the control panel of the test bench. The selected mode is lightened with the corresponding indicator.The equipment carries out testing of different alternators under load up to 200A. Power supply is single-phase 380V.
-
Measurements International Ltd.
The measurement of electric power and energy at high voltages and currents at low power factors is becoming increasingly important economically as a way to reduce costs in an ever-growing industrial economy. Today the transformer purchaser subjects the transformer manufacturer to an economic penalty for losses that occur in load and no-load conditions. To keep these penalties as low as possible, it is important that the manufacturer accurately measure these losses. Failure to do so can result in the manufacturer losing important contract awards to their competitors who may be utilizing a more accurate system. Using “State of the Art” proven two-stage-currentcomparator technology, the AccuLoss™ Series of transformer loss measurement systems is designed to meet the needs of today’s transformer manufacturer by providing the most accurate power loss measurement system in the world. Designed for power frequency testing and calibration, the AccuLoss™ system can be used for testing small, medium and large power transformers as well as motors and turbines up to 400 Hz. The system is also ideal for R&D facilities. The AccuLoss™ system can also be used to measure losses in single and three phase reactors.
-
EFT Series -
Jinan Testing Equipment IE Corporation
EFT series electric fatigue testing machine is an ideal platform to test a variety of materials and components for the following high demanding tests: Quasi-static test; Reverse-stress mechanical low cycle fatigue loading tests (LCF); High temperature creep, stress-rupture, relaxation tests in load/strain control mode for medium-term or long term period. Mechanical fracture tests like crack growth & toughness tensile/compression test for ceramics in both room- or vacuum-, high- temperatures up to 1200 C conditions etc. Compression test on plate springs or clutch springs etc. It is also widely used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastrometric materials, etc. It adopts electric actuator structure with all-elastic, backlash free, central ball-lead screw driving to achieve direct force transmission to the specimen, it is especially a perfect choice for R&D institutes, universities, nuclear power, automotive and aviation, & aerospace sectors from metals, composites, ceramics, springs and component parts.
-
Bruker Corporation
Bruker Semiconductor develops, manufactures, markets, and supports metrology solutions for thin films, which are based on novel, rapid, non-contacting and non-destructive X-ray technology. With Bruker’s acquisition of Jordan Valley Semiconductors, a name synonymous with unparalleled worldwide customer service and support, 75% of the world's top 25 semiconductor manufacturers rely on Bruker metrology tools for front-end and back-end applications, including development of their next-generation thin films. Bruker commitment to innovation and technology leadership drives the continued release of new advancements in metrology, and has garnered numerous awards and industry recognition. In applications ranging from C-S thin films materials characterization to wafer substrate analysis and defect detection, Bruker’s systems provide simulation analysis and fit. HRXRD, XRR, WA-XRD, and XRDI measurement types are fully supported, enabling researchers, production engineers, and process developers unparalleled capabilities. Whether you are a semi and C-S fabricator, R&D center or academy, or an industry materials research facility, Bruker has a specifically designed solution for your metrology needs.
-
Acces I/O Products, Inc.
Analog input boards are useful for measuring variably changing conditions in the real world. When we want to measure these variably changing conditions, we need analog inputs to convert these changing real world conditions to changing electrical quantities. For example, monitoring the temperature inside a wood kiln, or the water pressure on the output of a pump, or the heart rate of a medical patient. In each of these cases, you can use one of our analog input devices to convert the electrical data from a sensor or transducer into binary data that can then be used by your computer. The device that converts this data is known as an analog to digital converter (abbreviated ADC, A/D, or A to D). An analog input is a measurable electrical signal with a defined range. The analog input changes continuously in a definable manner in relation to the measured property. This data is very useful for process monitoring, process control, or simple monitoring / data collection and acquisition. ACCES' analog input boards amplify and multiplex input signals from thermocouples, strain gauges, accelerometers, photo sensors, flowmeters, RTDs, thermistors, voltage sources, millivolt sources, and current sources, just to name a few.
-
Site Sentinel CXT -
Teledyne Gas & Flame Detection
Command functions include alarm reset, alarm acknowledge, alarm test and radio silence. In normal operation the control panel provides real time display of gas concentrations or the status of other field devices; battery charge levels, network RF signal quality and any number of fault diagnostic conditions affecting either an individual field device or the entire network. These fault conditions are displayed on the control screen.Options include audio alarm, visual alarm, external alarm port, alarm reset switch and up to 4 external wired sensor inputs. Standard features include a power-in port and power switch.The control panel is rated for Class 1, Division 2; Groups A, B, C, D hazardous areas. Operator interface is non-intrusive via magnetic contact switches located behind the glass lens cover. This advanced design takes advantage of a low power LCD with back light and ultra low power components. Power is provided by an internal rechargeable battery and/or 11.5 to 30VDC. Operating time is 1-2 months before recharge is required. An optional solar charging panel can be used to extend operating time for virtually any application.
-
WinFT -
D&P Instruments
WinFT is our proprietary software which makes D&P instruments so functional and easy to winft1_largeuse. Based on the Windows operating system, this software provides simple and intuitive control of the instrument. All of the usual File functions are available, as well as controls over instrument settings such as resolution, apodization, zero-fill and number of coadds. Display options enable the user to display interferograms, spectra or both, as well as to adjust plot scales and units. Onboard math processing allows for real-time calculation of ratio, difference, and absorbance, and when using our calibrated hot-cold blackbody calibrators, the ability to measure calibrated radiance. Further, WinFT offers the ability to measure sample temperature in the radiance function by matching a Planck to the calibrated radiance. With the gold diffuse plate, the software can also compute and display absolute emissivity of samples. Our software also enables exporting of data files, now made even easier with our USB and LAN connections. In addition, the software has been designed to be easily run using the keyboard function keys and single letter commands, making the use of a mouse in the field optionalas well as minimizing key strokes when taking measurements in the field.