Showing results: 1861 - 1875 of 5363 items found.
-
7750TG -
Evertz Microsystems Ltd.
The 7750TG Test Signal Generator provides a cost effective method of generating SDTV 270Mb/s test signals. The 7750TG is ideal for checking signal path integrity, monitor alignment or to determine system performance over varying cable lengths. The 7750TG generates test signals in 525 line and 625 line SMPTE 259M-C video formats and offers four 270Mb/s outputs.
-
Magnetic Analysis Corp
Accurate handling, conveying and positioning of material, before, during and after the test is a critical part of any NDT system. MAC’s mechanical handling products, the result of many years of experience with actual NDT installations, help to ensure accuracy and successful test results. Standard and custom-designed options are available, plus “V” Roll and Constant Center Triple Guide Roll Test Benches.
-
1820 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
KT-5000Pi -
Kast Eng Co. LTD.
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
TS8996 -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
SemiProbe
Built using our PS4L patented technology, SemiProbe manufactures a family of Vacuum Probing Systems, which test wafers or substrates in a vacuum environment. Additionally, individual die and broken/partial wafers can be tested with the Vacuum Probing System. All key modules are interchangeable and upgradeable.
-
Power Diagnostix Systems GmbH
This group of instruments offer partial discharge measurement functions of different performance level. Devices for test and research laboratories as well as systems for on-site PD analysis are available. Stand alone units, computer controlled systems or wireless operating acquisition sets are shown in this area.
-
TRIO-TECH International
The COBIS-II Series Burn-in System is designed to test the latest high frequency integrated circuits (ICs) and combines a large capacity oven with well proven Accutron FlexBID™ dynamic driver technology. This system is engineered for productive dynamic device testing and reliable monitoring.
-
RAM-TEST-FIXTURE -
The Modal Shop, Inc.
The NDT Test Station, Model RAM-TEST-FIXTURE Resonant Inspection System is an ideal choice for testing when repeatable manual inspections are required. The innovative Test Station allows precise control of part positioning with an adjustable table ranging up to 6.25 inches (158.75 mm) in height.
-
CELL03 -
SDi
SDi offers a wide range of alarm component test tools to compliment our detector test equipment. These tools include devices for testing auxiliary components of alarm systems, such as batteries and audible appliances, as well testing solutions for more specialized fire detectors, such as duct and flame detectors.
-
TEM -
Mess- & Prüfsysteme GmbH
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
Keysight Technologies
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Keystone Compliance
The reliability test program includes a number of qualification tests based on the type of product, the environment within which it is anticipated to operate in and estimated product weaknesses. Establishing an effective but practical and affordable test program can be a challenge. Reducing the number of units tested or the scope of testing might not yield a sufficient sample of results. Testing multiple units or having an expansive test program can be very time consuming and expensive. A very good resource for establishing a reliability test program is MIL-HDBK-781: Handbook for Reliability Test Methods, Plans and Environments for Engineering, Development, Qualification and Production. This handbook provides test methods, test plans and test environmental profiles which can be used in reliability testing during the development, qualification, and production of systems and equipment.
-
Com-Power Corporation
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
