Showing results: 556 - 570 of 990 items found.
-
Security Intelligence Technologies, Inc.
The SSR-7000 consists of a radiation detection system that operates in concert with a MM Wave body scanner and an electronic countermeasure IED Defeat System. This three part solution is geared to deal with finding remote controlled weapons that are designed to detonate radioactive contents with a discharge that may or may not reach nuclear yield. Dirty bombs of this type are designed to cause terror and maximum panic.
-
Model 3442RA1 -
Jinan Testing Equipment IE Corporation
With gauge lengths of 1 and 2 inches (25 and 50 mm) and measuring ranges of 0.050 and 0.100 inches (1.2 and 2.5 mm), the Model 3442RA1 was designed for applications where tensile or compressive strength tests on small rock, concrete and other small compression samples is desired.
-
Model 4030 -
Jinan Testing Equipment IE Corporation
The Model 4030 extensometer uses a special LVDT-like sensor to measure strains on samples submersed in water or other compatible liquids. The unit is provided with the signal conditioning electronics. The extensometer is a semi-custom design, which is available in smaller measuring ranges up to 5 mm (0.2 inches). Clip-on (COD) style designs are also available.
-
Model 3542RA -
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
-
PP007-WS-1 -
Teledyne LeCroy
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
PP007-WR-1 -
Teledyne LeCroy
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
-
-
-
Teledyne LeCroy
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
-
-
GS Series -
Ono Sokki
All the GS series Digital Linear Gauges are upgraded. The GS-1700/1800 series is a compact and cost effective basic type. The GS-6700/6800 series is a vibration resistant type which provides better performance of vibration resistance 1.5 times in strength compared to the basic type. The GS-4700/4800 pursuits heavy-duty performance required in production site. Long stroke type the GS-5050/5100 series has wide measurement range (stroke) at 50 mm or 100 mm. Using ball bearing mechanisms in these all models greatly increases bearing life.
-
IAC90 -
D.Marchiori s.r.l.
D.Marchiori (DMA) manufacture electromechanical devices to measure the relative rotation between movable surfaces which are used by the aircraft industry for aircraft control surface analysis.Angular position is measured by a goniometric scale and/or by an angular position sensor with 0.01 deg. resolution. Angular protractors can be supplied with two types of fixing plates: the screw-type plate and the suction-type plate. A special bearing on the mounting and a cylindrical hinge allows the protractor to check the relative rotation between movable surfaces having a transversal misalignment of 0.8 inch (20 mm) max.
-
KNM X series -
KAPP NILES Metrology GmbH
machine structure with outstanding intrinsic accuracylarge bearing distances of guidesinherently stable granite machine base on active dampers to absorb vibrations ? no foundation requireddrive system close to center of gravitylinear motors in X-, Y-, Z- measuring axeshigh precision air- or hydrostatic bearing rotary tables (diameters from 500 to 1,800 mm) with direct drive and through holemotorized positioning of measuring column (V-axis) to the actual workpiece diameterlaser based system for safe operation