Showing results: 46 - 60 of 104 items found.
-
HMa -
Lectrosonics, Inc.
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
VM-560FF -
Vivax-Metrotech Corp
The VM-560FF Transmitter has one induction frequency; three direct connect and a fault-find frequency. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection. This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.
-
SEM206P -
Labfacility Ltd.
The SEM206/P is our entry level PC programmable temperature transmitter. It accepts Pt100 temperature sensors and converts the sensor output to a standard industrial (4 to 20) mA transmission signal.
-
CO-R -
Automation Components Inc.
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
HR6100 -
HighReach Measuring & Controlling System Co.,Ltd
The HR6100 input-type integrated temperature transmitter uses an imported temperature sensor to transmit and output RS485 standard signals through a built-in microprocessor. The product adopts the sealing structure of the liquid level transmitter, the waterproof cable outlet, the 316L stainless steel casing, And the temperature probe to the front end, which is suitable for occasions with special requirements on the installation dimensions.
-
LVRD10 Series -
Omega Engineering, Inc
The LVRD10 Series guided wave radar transmitters provide continuous level measurement with a 4 to 20 mA signal output. Offered in single rod, coaxial, or weight & cable probes in 3 or 6 foot lengths
-
Herrin Design & Manufacturing Co.
Herrin Design’s Model HD3011 Tide Gauge is an ocean tide monitoring system designed for use in dredging, on ships, on survey vessels or for any other application where accurate tidal data is required. The tide gauge system has two components, a transmitter and a receiver which communicate using a radio link. The transmitter uses a sensitive pressure transducer to measure precise changes in tide levels.
-
MS 1522 -
Meltronics Systemtech
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
5081 -
Barben Analytical
The Model 5081 family of transmitters can be used to measure pH, ORP, conductivity (using either contacting or toroidal sensors), resistivity, oxygen (ppm and ppb level), free chlorine, total chlorine, and ozone in a variety of process liquids.
-
Lumistar Inc.
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
Series 668B/D -
Dwyer Instruments Inc.
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
DPR -
Lectrosonics, Inc.
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
-
NOSHOK, INC.
NOSHOK Digital Indicators provide local indication for pressure, level and temperature transmitters. The NOSHOK Attachable Loop Powered Digital Indicator can easily be fitted to NOSHOK pressure transmitters utilizing a 4 mA to 20 mA output signal and the Hirschmann (DIN 43650A) connector. NOSHOK also offers a dual display model that accepts a wide variety of input signals including thermocouples or RTDs, current, voltage, resistance and process signals. Plug-in option cards are available on several models for field upgrading.
-
HR3051-DP -
HighReach Measuring & Controlling System Co.,Ltd
The HR3051-DP differential pressure transmitter measures the level, density, pressure, and flow of a liquid, gas, or vapor and converts it into a 4-20 mADC HART current signal output. The HR3051-DP can also communicate with the RST375 handheld (standard area of the RSM100 Modem for parameter setting, process monitoring, and more.
-
681 -
Dwyer Instruments Inc.
The Series 681 Sanitary Pressure Transmitter is designed to meet 3A standards for applications in food, dairy, beverage and pharmaceutical processing, liquid level control, and sanitary pipelines. The unit is fully sealed to withstand high pressure washdown in Clean-in-Place (CIP) and Sterilize-in-Place (SIP) installations.