Showing results: 61 - 75 of 267 items found.
-
Fortress Technology Inc.
Phantom Gravity metal detector systems are designed to detect metal contamination in dry, powdery or granular free-flowing products that can be gravity fed through a pipe. Systems are available in Aluminum or Stainless Steel casings, with a selection of pipe sizes. The Diverter Valve reject system is typically used to divert contaminated product into a reject tank.
-
KROHNE Messtechnik GmbH
OPTITEMP smart compact sensors for temperature measurement in gases and liquids, in pipes and tanks at medium pressure and flow
-
U1183A -
Keysight Technologies
Measure dryer, transport pipe, and surrounding air temperature within the range of -50°C to 800°C.
-
VEGA Grieshaber KG
In flow measurement, the amount of material that flows through a certain pipe cross section per time unit is measured.
-
WNRS -
Seismo Wave
The Wind-Noise Reduction System (WNRS) is an array of air inlets connected with pipes to reduce wind-noise and improve signal quality.
-
1OVX606MZ3-1X01R -
ELMA Electronic, Inc.
VPX mesh, 4 lane Fat Pipe, QFP expansion plane, up to 6.25 Gbps per channel
-
2540 -
Georg Fischer Signet
The Signet 2540 Paddlewheel Flow Sensor offers field-replaceable electronics and transient voltage suppression (TVS) to provide greater immunity to large voltage disturbances (i.e. lightning) sometimes encountered in field wiring. Sensors can be installed in DN40 to DN600 (1 to 24 in.) pipes using the 1 inch NPT or ISO 7/1-R 1.5 threaded process connection. The sensors are also offered in a hot-tap configuration with a bleed valve service without process shutdown in pipes up to DN900 (36 in.). Both styles of sensors must be used in full pipes and can be used in low pressure systems.
-
RF096-18/30-155/307-HH Series -
RIFTEK LLC
The gauge is designed for non-contact scanning and measurement of the inner diameter (wear) of pipes. ID measurement range, mm / 18…30
-
MS3112 -
Metal Samples Company
The Hydrogen Penetration Monitoring System™ provides a method for directly measuring the rate of hydrogen migration through a vessel or pipe wall. This method actually measures the penetration current set up by the hydrogen as it moves through the steel. By sensing and recording this data directly from the pipe wall, this system offers valuable data which can only be indirectly inferred by other methods.
-
MINIFLEX -
Camtronics bv
The MiniFlex is a flexible sewer camera that has been specially developed for inspecting small diameter pipes, drains and tubes (32mm - 100mm). Mostly found in for example sanitairy rooms, plumbing and kitchens. This kind of sewer inspections needs flexibility due to the width of the pipe including the numerous bends and the position to manoeuvre into and to be able to carry out a camera inspection with a mini sewer camera.
-
KATflow 100 -
Katronic
The KATflow 100 is a compact clamp-on ultrasonic flow transmitter with a robust and practical design for permanent installation and flow measurement on single pipes.
-
-
Amprobe Test Tools
Eliminate unnecessary digging or demolition by showing you where energized and de-energized wires, cables and pipes are located before you dig.
-
SKZ146A -
SKZ Industrial Co., Ltd
Applied to test the impact roughness of non-metallic materials such as hard plastic board, pipe, reinforcednylon, glass steel, ceramics and molten insulating material.
-
PeakTech Prüf- und Messtechnik GmbH
Is a thermal imaging camera with a thermal resolution of 160x120 thermal image points with a high-quality sensor, which makes even the smallest temperature differences visible. All thermal images can be opened and evaluated using the enclosed software, with subsequent changes, e.g. can be done on the pallet selection. Use this new development to find thermal bridges in thermography, leaks in systems and pipe systems or track heating pipes in walls and floors.