Showing results: 256 - 270 of 440 items found.
-
Extech MG500 -
Extech Instruments Corporation
The MG500 is a digital high voltage insulation tester that tests voltage up to 10kV and measures insulation resistance to 500GOhm. The MG500 has a CAT III 300 Volt safety rating. This product is complete with a year warranty, built-in heavy duty carrying case with cover, test leads, alligator clips, and 8 x C batteries.
-
6201 IN (Ranges: 5kV, 10kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● High quality Taut Band movement.● Two insulation test voltages.● Insulation resistance, auto ranging on all ranges.● Low Battery LED indication.● Beeper warning of external voltage.● Fully protected : crow bar.● Housed in carry case.
-
IST Engineering, INC.
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
Hubbell Power Systems Inc
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
Rohde & Schwarz GmbH & Co. KG
Only conformance test sytems from Rohde & Schwarz cover all relevant digital mobile device generations.The key to success is comprehensive access to RF, RRM, LBS and PCT test cases as defined e.g. for 5G NR in 3GPP TS 38.521-1 to -4 (5G NR RF), 38.533 (5G NR RRM), 38.523-1 (5G NR PCT), 37.571 (LBS).The Rohde & Schwarz conformance test solution portfolio consists of approved test platforms for device certification by GCF and PTCRB that support both TDD and FDD and all relevant 5G NR bands in both sub-8GHz (FR1) and mmWave (FR2) frequencies, as well as all frequency bands for LTE, WCDMA and GSM.
-
Fieldpiece Instruments, Inc
Digital Megohm Meter, model SMG5, is a compact standalone meter designed for checking HVAC compressor insulation. The SMG5 provides a 1000V voltage source, monitors current, and displays the resistance between the test points. Maximum current output is <1mA. It can be used to determine the condition of insulation from winding to ground in a motor, compressor, or transformer. Includes a case, alligator clip lead tip and leads with removable tips.
-
MD-AWD-150 Series -
Mustang Dynamometer
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle.
-
Dynatest -
PASI srl
*Extractometer used to measure and check the strength of fixing parts*Test carried out with a four-arm wheel or (and) the hydraulic pump with crank*Results on a pointer/digital indicator with peak value*Lightweight and easy to handle*Simple and quick setting up*Appropriate for on site testing*Packaged in a transport case (with a set of optional accessories)*Revolution counter for the crank*Delivered with a calibration results and the copy of the calibration report for the reference standard sensor
-
M+P International
The Mixed Mode add-on modules for the Random Vibration Control Software allow tests to run with sine tones and/or narrowband random signals superimposed on a random background. Mixed mode testing is a complex control task, and m+p VibControl supports three modes: Sine-on-Random (SoR), Random-on-Random (RoR) and Sine-on-Random-on-Random (SoRoR). Gunfire burst control can also be superimposed in each case.
-
Amprobe Test Tools
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
Datum Electronics, Ltd.
Datum Electronics are able to provide both modular and custom designed torque and rotary strain measurement solutions, which can be complete as one off or as fully integrated OEM solutions.In many cases, it is better to use an existing shaft or test rig and use custom industrial sensors instead. This process reduces the cost of fitting a conventional torque transducer and it improves the torque measurements, taken by maintaining the dynamics of the driveline.
-
SeqZap -
CIM Software Testing A/S
Use SeqZap to automate your software test and save a lot of time in development projects. The primary goal for SeqZap is to enable professional, easy and pragmatic automation of system testing. System Testing Automation is both the formal test discipline of automating the execution of the system testing test cases during the software development phase of a product, but it is also the ad-hoc testing done throughout the whole product development life cycle.
-
380320 -
Extech Instruments Corporation
The 380320 is an Analog Insulation Tester with a large, easy to read analog display. Featuring a live circuit warning which displays the actual AC voltage measurement, Automatic discharge circuit, Lock Power On feature for extended test times, and Insulation resistance up to 400MΩ. Complete with heavy duty test leads, alligator clip test lead, 6 x AA batteries, hanging strap and hard carrying case.
-
James Instruments Inc.
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
UTOR
Production teams often refer to automation testing like it’s the holy grail. But when it comes to user experience, there’s no replacement for the human eye. While automated tests focus on repetitive tasks, manual QA testers come up with creative use cases and provide a lot more value. Very often, our recommendations helped improve the products and even lead them in new, more successful directions.