Showing results: 316 - 330 of 351 items found.
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
6280 TB -
Standard Electric Works Co., Ltd
● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1
-
19070 -
Chroma Systems Solutions, Inc.
The Sentry 19070 Hipot Tester series provides 2 models to choose from. The Sentry 19071 for AC Hipot testing; and the Sentry 19073, which combines both AC and DC Hipot with insulation resistance (IR) measurements into a single compact unit.
-
LXinstruments GmbH
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
-
MCL-400IR+ -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
MTC 3 -
Whitelegg Machines Ltd
The fully automatic MTC3 stator testers test your windings reliably and quickly for possible insulation faults via our patented surge voltage test.After connecting the test object completely the test is performed with an automatic switching of the connections and the test methods. The MTC3 evaluates each test step. At the end of the complete test process it provides a clear and reproducible GO or NO GO-statement.
-
C Model -
PJ Electronics, Inc.
These Digital High Frequency Surge Testers are the ultimate in ruggedness & durability. Fourteen / sixteen gauge steel construction and mobility on 6" heavy duty rubber wheels makes it a favorite for use in harsh industrial environments. The performance of PJ's exclusive/unique High Frequency Technology is capable of testing the integrity of any turn-to-turn insulation, including low inductance windings.
-
2678X -
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
HopeTech
program-controlled safety tester includes CHT9910 / 9912/9922; it has AC / DC withstand voltage test and insulation resistance test function; it has 6 groups of test modes and can realize programmable test.AC / DC voltage output 10V ~ 5KV / 6KV, insulation resistance test range: 100KΩ ~ 99GΩ, meanwhile, it has arc detection and over power detection functions. Optional RS485 interface, you can easily experiment with instrument networking through MODBUS communication protocol.
-
446 -
SCI
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
Shanghai Dean Electrical Co., Ltd
Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.
-
SUG255 -
Lisun Electronics Inc.
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
Salicon Nano Technology
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.GW Instek’s GPT-9900/GPT-9800/9600 series safety testers(hipot test) provide safe and quick measurement tools for AC/DC withstanding voltage tests, insulation resistance tests, and AC ground bond tests. Those tests are required by many international safety regulations such as CE, UL, VDE, and etc. We also have leakage current tester, GLC-9000, which supports all the major leakage current test standards for medical and general electronic equipment.
-
Banair
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
HDYD-5kVA/50kV -
HD Power Test Equipment Co.ltd
The Hipot test is a nondestructive test which is effective way to determine the insulation strength for electric equipment . Our Hipot Tester can check dangerous flaws and make sure electric equipment continuous working. It is widely used on transformers, switchgear, cables, capacitors,aerial motors platforms and other related equipment like vacuum interrupters, blankets,instruments transformers generators.