Showing results: 4261 - 4275 of 5178 items found.
-
40-675B-002-10/16 -
Pickering Interfaces Ltd.
The 40-675B-002-10/16 (PXI) and the 42-675B-002-10/16 (PXIe) are 10-channel, 16-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
40-675B-002-24/8 -
Pickering Interfaces Ltd.
The 40-675B-002-24/8 (PXI) and the 42-675B-002-24/8 (PXIe) are 24-channel, 8-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
40-675B-002-49/4 -
Pickering Interfaces Ltd.
The 40-675B-002-49/4 (PXI) and the 42-675B-002-49/4 (PXIe) are 49-channel, 4-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
Shijiazhuang Zhongshi Testing Machine Co., Ltd.
The instrument is used for testing the main material of Polyethylene blown covering film and ethylene-vinyl acetate copolymer(EVA),the average content of Vinyl Acetate(VA)is not less than 4% of the anti-dripping progerty blown covering film within add-type. This instrument is mainly testing the first dripping beginning time and the anti-dripping failure time of the film. It is the ideal testing equipment for science research department, universities, commodity inspection, laboratory, graduate school and quality supervision departments
-
SDT-40KW -
Zhejiang Sandi Electric Co., Ltd
SANDI SDT series single-phase to three-phase converter, adopted SVPWM modulation control technology, which can convert ordinary single-phase power to industrial three-phase power. After through SDT series single-phase to three phase converter power conversion, the three-phase power output is standard pure sine wave, the harmonic distortion rate (THD) is less than 2%, totally meet the national standards of three-phase power quality, applicable to all types of load.
-
LV-7000 series -
Ono Sokki
The LV-7000 series detects speed, uneven speed, distance, length of moving object or rotating object without contact. By contacting with 2 sensors, it enables to calculate difference in velocity/length between the two points in real time and output with 3,000 ppm of accuracy. The frequency response can be expanded up to 20 kHz, which achieves to understand phenomena and evaluate mechanical systems at high speed, efficiently, and accurately. It is useful for evaluation of motor control and behavior measurement, improving parts quality, and reducing loss of material.
-
FC Series -
Semiconductor Circuits, Inc.
The FC Series are ultra-low noise, high performance DC/DC converters that are packaged in low profile (0.4 inch high) cases. Essential quality performance features are designed and built-in. A high performance Pi input filter minimizes input reflected ripple, while 5-sided electrostatic shielding and tape-wound toroids, rather than pot cores, minimizeradiated EMI. Advanced circuit design techniques reduce conducted output noise in the form of current spikes, to an extremely low level.
-
MiniFlex -
Rigaku Corp.
New sixth generation MiniFlex X-ray diffractometer (XRD) is a multipurpose analytical instrument that can determine: phase identification and quantification, percent (%) crystallinity, crystallite size and strain, lattice parameter refinement, Rietveld refinement, and molecular structure. It is widely used in research, especially in material science and chemistry, as well as in industry for research and quality control. It is the newest addition to MiniFlex series of benchtop X-ray diffraction analyzers from Rigaku, which began with the introduction of the original MiniFlex system decades ago.
-
LQ6324T -
Aplab Limited
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
CryoTel® -
Sunpower Inc.
With Sunpower’s reputation for quality and performance, the CryoTel® family of cryocoolers is increasingly used in the medical, instrumentation, security, astronomy, telecommunications, and pharmaceuticals markets. Sunpower’s cryocoolers integrate with and support technologies such as high-temperature superconductivity, radiation detection, optics, CCD, LNA, gas liquefaction, and more. The CryoTel® cryocoolers provide cost advantages during product development and during volume production. Our customers also benefit from the unsurpassed reliability, efficiency, and power density of our superior cryocooler technology.
-
SurfaceC‑800 -
ELTRA GmbH
Determination of surface carbon is a special requirement for quality control in the metal producing and metal working industry. ELTRA’s SurfaceC-800 analyzer is designed for the precise determination of surface carbon in numerous kinds of solid samples from trace level up to 1000 µg/cm2. The SurfaceC-800 is equipped with a resistance furnace with quartz tube for sample oxidation and can provide temperatures up to 1000 °C. The temperature of the SurfaceC-800 can be set up in steps of 1 °C. As common carrier gas in the SurfaceC-800 oxygen is used.
-
CPM-70 -
Chuan Sheng Electronics Co., Ltd.
CPM-70 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication.CPM-70 series meters are able to measure bidirectional, four quadrants kWh and kVarh.It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2 MB flash for data-logging.
-
ficonTEC Service GmbH
The laser diode is one of the most common devices used throughout photonics. The micro-assembly process calls for the placement and bonding (align-&-attach) of single emitters, or multiple laser diodes (stacked or complete bars), the placement, active alignment and bonding of necessary micro-optical elements, subsequent device testing, and ultimately packaging and quality control. ficonTEC’s machine systems are capable of all the steps necessary for assembling laser diodes, even high-power devices. Multiple in-line systems can be configured to address entire process segments.
-
MFI -
Rhopoint Instruments
The Hanatek Melt Flow Indexer (MFI) is one of the most advanced instruments available for the measurement the melt characteristics of thermoplastic polymers.Understanding melt flow is a key indicator for producers, processors and converters of plastic materials as it dictates the temperatures and pressures required to manufacture consistent quality productsActual barrel temperature can be measured to ensure that every test is performed with complete compliance to ASTM D1238 (2011) Part A, B or C and ISO 1133 (2011) with full test documentation.Test TypesMFI/MFRMelt Volume RateMelt DensityShear Stress/RateMelt Viscosity
-
ZEISS Xradia Versa -
Carl Zeiss AG
Extremely versatile ZEISS Xradia Versa 3D X-ray microscopes (XRM) provide superior 3D image quality and data for a wide range of materials and working environments. Xradia Versa XRM feature dual-stage magnification based on synchrotron-caliber optics and revolutionary RaaD™ (Resolution at a Distance) technology for high resolution even at large working distances, a vast improvement over traditional micro-computed tomography. Non-destructive imaging preserves and extends the use of your valuable sample, enabling 4D and in situ studies.
