Filter Results By:
Products
Applications
Manufacturers
Conduit
1) channel's liquids or solids. 2) means of protecting wire or wireless connections.
See Also: Pipeline, Wireless Test
- Virginia Panel Corporation
product
Threaded Coupling Adapter, G2, G6, G10, ITA, For Conduit Harnessing Assemblies/Clamps
410112599
The Adapter is designed to accommodate military and commercial circular backshells for conduit or strain relief when designing for general and heavy-duty applications. The male thread size is 1.625-18 for this application.
-
product
Circuit Tracer, Inductive Clamp
61-958
*Induces a signal in a conductor*1 in. jaw opening/6 ft. cord*Works on de-energized circuits and energized circuits up to 5A, also low voltage wiring and metal conduit*Powered solely by a separate battery pack (supplied with 8 C-cell batteries)
-
product
Conduit Bending Tester
King Design Industrial Co., Ltd.
Equipment complies with IEC 61730-2:2004 MST 33 specification.
-
product
Dike-Type And Partial Flume-Type Flowmeter
These flowmeters provide the means for flow measurement and flow control of open conduit channels in water supply facilities and sewage facilities.
-
product
Industrial Pressure Transmitter
628
The Dwyer Series 628 Pressure Transmitters are ideal for OEMs with 1% full scale accuracy sensors. The transmitter is also available in the general purpose stainless steel housing and the cast aluminum conduit housing.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
Rolling Seal 8 Optical Connector (RS8)
The patented Rolling Seal design functions by excluding water and shuttling silt away from the region where the optical ferrules are brought into contact as the connectors are mated. As a result, a clean oil-filled conduit is created for the optical ferrules to connect. The result is a reliable lowloss optical throughput.
-
product
Shaft Speed Sensors - Magnetoresistive
1102 / 932 / 933 XP
Features• Square-wave pulse frequency output, NPN open-collector• Zero speed operation with no signal loss• 5-24 VDC powered• 1/2" NPT conduit port (933 XP)• Non-contact, large gap distance sensing• Simple to install and set up• Works with Electro-Sensors magnetic pulser discs / wraps• 1102 – non-threaded stainless steel
-
product
Speed Sensors Dust Ignition-Proof
ST420-LT / ST420-DI
Features • 2-wire, loop-powered 4-20 mA analog output • No user calibration – works right out of the box • Standard and custom measurement ranges available • Reverse-wiring protected Rugged stainless steel M18x1 housing with integral conduit attachment; FM approved, dust ignition-proof. Class II, Div I (E, F, G); NEMA 4X, IP65
-
product
Submersion Level Detector
SL-180C
For waste water and sewage water facilities: Pumping stations, Flow conduits in treatment plants and so on.
-
product
Temperature Sensors
TT420-LT
Features • 2-wire, loop-powered 4-20 mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Integral 1/2" flexible liquid-tight conduit fittings • TT420Z-LT 1/4” stainless steel probe with 1/8 NPT adapter • TT420S-LT 3/8-16 threaded stud probe • FM approved, Dust Ignition-proof • Class II and III, Div I (E, F, G); NEMA 4
-
product
Cables, Harnesses & Wiring Looms
Amfax manufacture a wide range of wiring harness solutions in a variety of styles and finishes. These wiring harnesses, or looms as they are often called, can be constructed using heat-shrink, conduit tube, braid, tape, tie-wraps or lacing cord.
-
product
Concrete Imaging with Ground Penetrating Radar GPR
Conquest 100
Conquest GPR: Get rapid, reliable results and reduce the need for destructive testing. Conquest GPR is a light, portable device that provides a fast, non-invasive method to gain accurate insights of objects below the concretesurface, even on a curved surface or column. Conquest GPR reduces risk by detecting rebar, post-tension cables, metallic and non-metallic conduits as well as current-carrying wires embedded in concrete. Once your concrete scan is complete, Conquest GPR connects to your mobile device, allowing you to email information directly from the field. Back in the office view your data and make client-ready reports in minutes.
-
product
Temperature Sensors
Screw in positive mount installationGrease zerk for bearing lubrication1/2” NPT conduit entry (steel body)NTC version - continuous temperaturePTC version - trip points from 122°F to 194°FPT100 version - platinum RTDClass 2 Div 1, Div 2 Approved
-
product
Specialized Application Performance Monitoring
Foundation APM
Foundation APM delivers incomparable system health and availability customized for UC and Contact Center assets. Designed to meet the needs of enterprises and service providers, Foundation APM is powered by Nectar’s Remote Intelligence Gateway, which also functions as the on-premises conduit for connecting private datacenter monitoring to Nectar’s cloud.
-
product
Industrial Weighing - Wireless Load Cells
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
product
Entry Level GPR System for Concrete Inspection
StructureScan Mini LT
Geophysical Survey Systems, Inc.
The StructureScan™ Mini is GSSI’s all-in-one GPR system for concrete inspection. This handheld system locates rebar, conduits, post-tension cables, voids and can be used to determine concrete slab thickness in real-time.
-
product
Ethernet Flying Lead
Qualified 100m Subsea Ethernet jumpers designed for data transmission and real-time situational awareness and monitoring. The typical Ethernet harness system consists of wet-mateable, Nautilus connectors, Nautilus penetrators, and pressure balanced, oil-filled (PBOF) hose conduits. Internally, the Ethernet signals are transmitted over custom Ethernet cabling sealed to seawater ingress by two independent barriers. Seven and 12-way configurations are available. Subsea connection of the harnesses may be accomplished by ROV, Diver-Mate or Stab-Plate applications. For Ethernet needs above 100 meters, see Extended Ethernet Flying Leads.
-
product
GPR System for Concrete Inspection
StructureScan Mini XT
Geophysical Survey Systems, Inc.
The StructureScan Mini XT is GSSI’s newest generation of our very popular all-in-one GPR systems. The StructureScan Mini XT offers a 2.7 GHz antenna for superior target resolution and can reach depths of 20 inches (50 cm). Ideal for locating rebar, conduits, post-tension cables, voids, and real time determination of concrete slab thickness.
-
product
Wireless Connectivity 4 in 1 Digital Multi Detector with moisture measurement
MS-W68(11B)
External wireless connectivity 4 in 1 Digital Multi Detector can detect live wires and metal pipe / conduit in walls and wooden stud in drywalls, with audible and numerical display on LCD.
-
product
Utility Locator
VM-850
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-850 operates at a much lower frequency of 9.82kHz which is ideal for smaller diameter utilities such as CATV, power and telephone with less bleeding onto adjacent services.
-
product
PipeTRACK Traceable Duct Rodder
Ideal for line tracing buried non-metallic telecom HDPE conduits, metallic pipes or utility lines.
-
product
Cable Locating Kit
CL-300
The NEW CL300 cable locating kit consists of a portable, holstered pipe & cable locator with an industry accepted 33kHz transmitted frequency. Comes standard with 512 Hz detection capability. With an added 512Hz transmitted device or traceable duct rodder the CL300 becomes the perfect tool for empty duct work locating. This instrument is capable of detecting all electrical, telecommunications and wire circuits—whether direct buried cables or those within conduits—using direct connect or close induction methods. This locator equipment features Auto & Manual adjustments for both transmitter power and receiver sensitivity to assist with a variety of locate work and congestion.Applications
-
product
Wireless Connectivity 3 in 1 Digital Multi Detector
MS-W68(11A)
External wireless connectivity 3 in 1 Digital Multi Detector can detect live wires and metal pipe / conduit in walls and wooden stud in drywalls, with audible and numerical display on LCD. One of the advantage of the digital multi detector is wirelessly connect to Smart phone / Tablet / PC to view data, record reading, capture picture with data on it and send the information to headquarter.
-
product
Utility Locator
VM-810
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-810 operates at 83.1kHz which is ideal for water and gas utilities which generally are larger pipes with bell housings and gaskets. The VM-810’s higher frequency is also good for locating ungrounded small diameter drop wires and inducing signals through the soil, onto services when direct connecting is not an option.
-
product
General Purpose Surface Temperature Assembly
S2-2
The Series S2-2 General Purpose Surface Temperature Assembly is ideal for monitoring the temperature of indoor distribution lines when it is not possible to penetrate the pipe. The plastic housing is in the shape of a standard junction box with multiple knockouts for easy conduit access. The strap-on connection quickly wraps around a pipe and can be securely tightened using a flat head screw driver. The Series S2-2 can be ordered with a choice of 11 output options that allow it to communicate to any standard building control system
-
product
Insertion Flow Meter
SPI Mag
The SPI Mag Insertion Flow Meter provides a highly cost-effective solution for the accurate measurement of liquid flow in closed conduit, pressurized pipe applications. Unlike conventional magnetic meters, the SPI Mag's cost is independent of pipe size.
-
product
Vertical Entry Liquid Level Pressure Sensor
LL-V
The rugged Model LL-V vertical entry submersible liquid level sensor from Honeywell Sensotec can be suspended in an open tank or attached to the crown of an enclosed tank and used to any depth. The atmospherically vented oceanographic cable assembly exits through a 1/2-14 NPT threaded conduit connection that allows mechanical or chemical protection tubing or pipe to be threaded on over the cable.
-
product
RF Filters
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
