Showing results: 91 - 105 of 328 items found.
-
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. This Wear Testing Machine complies with ASTM D3514/D3885/D3886, AATCC 119/120, FTMS 191/5300/5302, etc.
-
Labodam
Labodam Engler Viscometers are designed according to the ASTM D1665 Test Methods for Engler Viscosity of Petroleum Products standard. It is devised with digital temperature controller and its chambers are made with stainless steel to avoid corrosion.
-
807 -
TRICOR Systems Inc.
TRICOR’s Hazer Meter and DOI is ideally suited for measuring flat, non-textured high reflectance surfaces. The Model 807A Haze Meter design is in accordance with ASTM E430 and ASTM D5767 (method A) and is used to measure ±3 degrees around the specular lobe centered at 30 degrees in approximately 220 increments. That’s an angular sample size of 1 sample per 1.6 minutes of arc! This allows differentiation between samples with very small differences in reflectance characteristics. Verified replacement for the older Hunter Dorigon II haze meter unit.
-
K613S -
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the flash point of petroleum products by Cleveland open cup.Conforms to GB/T 3536, GB/T 267 and ASTM D92.Except fuel oils and petroleum products having an open cup flash below 79℃
-
K612 -
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the flash point of petroleum products by Cleveland open cup.Conforms to GB/T 3536, GB/T 267 and ASTM D92.Except fuel oils and petroleum products having an open cup flash below 79℃
-
K10610 -
Chongqing Kailian Yongrun Industrial Co.,Ltd.
Under controlled test conditions, measure the change in consistency of lubricating grease after mechanical shearing work., then, to detemine the mechanical stability of lubricating grease. (The unit of shear stability is 1/10mm.)Conforms to GB269 and ASTM D217.
-
EBS/ECS-SERIES -
Envisys Technologies
EBS/ECS Series Salt Spray Chambers (Basic & Cyclic) are manufactured by Envisys in different versions to meet the diverse testing applications as per various international standards viz., ASTM, DIN, GM, JIS, MIL etc.,
-
Jinan Saicheng Instrument
Falling dart impact tester can be used for the determination of impact resistance of packaging materials such as plastic films, laminates by a free falling dart from a certain height. This instrument is designed according to ASTM D1709 with method A & B.
-
EKT-2002FF -
Ektron Tek Co., Ltd.
EKT-2002FF Flexing Fatigue Tester is designed in accordance with ASTM D4482 to test the fatigue life under a tensile strain cycle on different kinds of vulcanized rubber compound to determine the fatigue life at various extension ratios.
-
XCell -
Giatec Scientific Inc.
Giatec XCell™ is a smart tablet-based NDT probe for fast, accurate and efficient detection and on-site analysis of corrosion in reinforced concrete structures. Giatec XCell™ meets all the requirements of the ASTM C876 standard specification.
-
Tinius Olsen
Tinius Olsen is proud to introduce our latest evolution of melt indexer to meet almost every need. This new model, the MP1200, meets, and surpasses, all the requirements of Procedure A and Procedures B, C and D of ASTM D1238.
-
TF350 -
TESTEX Testing Equipment Systems Ltd.
Smoke Density Tester , is widely used for density determination of smoke from the burning or decomposition of plastics and building material, designed according to ASTM D2843 and GB/T 8627. Equipped with high accuracy PLC and colorful touch panel.
-
Hildebrand Prüf- und Meßtechnik GmbH
The MICRO IRHD SYSTEM provides hardness readings on elastomers according to MICRO IHRD. Recommended specimen thickness is 1 to 5 mm. It complies to international standards such as DIN ISO 48, ISO 48 and ASTM D 1415.
-
LP471UVA -
Delta OHM S.r.L.
Radiometric probe for measuring the IRRADIANCE in the UVA spectral range 315 nm…400 nm, peak at 360 nm, quartz diffuser for cosine correction. For non-destructive testing ISO 3059:2001, EN 571-1, ASTM E1417.
-
Instron
Provides system control, data acquisition, real-time graphs, calculation of results, storage of data to disk, and post test graphs and reports in accordance with the relevant sections of ASTM E606-04, BS 7270 (2006), and ISO 12106 (2003).